DataSheet39.com

What is PSN25-5AO?

This electronic component, produced by the manufacturer "Autonics", performs the same function as "INDUCTIVE PROXIMITY SENSOR".


PSN25-5AO Datasheet PDF - Autonics

Part Number PSN25-5AO
Description INDUCTIVE PROXIMITY SENSOR
Manufacturers Autonics 
Logo Autonics Logo 


There is a preview and PSN25-5AO download ( pdf file ) link at the bottom of this page.





Total 1 Pages



Preview 1 page

No Preview Available ! PSN25-5AO datasheet, circuit

INDUCTIVE PROXIMITY SENSOR(SQUARE AC 2WIRE)
PSN SERIES
MANUAL
Thank you very much for selecting Autonics products.
For your safety, please read the following before using.
▣ Caution for your safety
※Please keep these instructions and review them before using this unit.
※Please observe the cautions that follow;
Warning Serious injury may result if instructions are not followed.
Caution Product may be damaged, or injury may result if instructions are not followed.
※The following is an explanation of the symbols used in the operation manual.
Caution:Injury or danger may occur under special conditions.
Warning
1. In case of using this unit with machineries(Nuclear power control, medical equipment vehicle,
train, airplane, combustion apparatus, entertainment or safety device etc), it is required to
install fail-safe device, or contact us for information required.
It may cause a fire, human injury or property loss.
Caution
1. Do not use this unit in place where flammable, explosive gas, chemical strong alkalis, or acids exist.
It may cause a fire or explosion.
2. Do not impact on this unit.
It may cause malfunction or damage to the product.
3. Do not use this unit beyond rated power.
It may result in serious damage to the product.
▣ Ordering information
P SN 25 5 AC
Control output
Sensing distance
Dimension
Shape
Item
AO Normally Open(N.O.)
AC Normally Closed(N.C.)
Number Sensing distance(Unit: mm)
Number A side length(Unit: mm)
SN Square
P Inductive proximity sensor
▣ Control output diagram & Load operating
Brown Load
Blue
100-240VAC
50/60Hz
Sensing
target
Normally
Open
Presence
Nothing
Load Operation
(Brown-Black) Return
Indicator
(LED)
ON
OFF
Normally
Closed
Presence
Nothing
Operation
Return
ON
OFF
▣ Connection of the power supply
Be sure to supply the power after connecting the load, because direct connection of the proximity sensor may
cause damage to the inner elements of this product.
100-240VAC
50/60Hz
Load
100-240VAC
50/60Hz
※ The above specifications are subject to change without notice.
▣ Specifications
Model
PSN25-5AO
PSN25-5AC
PSN30-10AO
PSN30-10AC
PSN30-15AO
PSN30-15AC
PSN40-20AO
PSN40-20AC
Sensing distance
Hysteresis
Standard sensing
target
Setting distance
Power supply
(Operating voltage)
Lackage current
Response frequency
Residual voltage
Effect by Temp.
Control output
Insulation resistance
Dielectric strength
Vibration
Shock
Indicator
Ambient
temperature
5㎜
25×25×1㎜(Iron)
10㎜
15㎜
Max. 10% of sensing distance
30×30×1㎜(Iron) 45×45×1㎜(Iron)
20㎜
60×60×1㎜(Iron)
0 to 3.5㎜
0 to 7㎜
0 to 10.5㎜
0 to 14㎜
100-240VAC 50/60Hz
(85-264VAC)
Max. 2.5mA
20㎐
Max. 10V
Within ±10℃ max. of sensing distance at 20℃ in temperature range of -25 to 70℃
5 to 200mA
Min. 50㏁(at 500VDC megger)
1,500VAC 50/60㎐ for 1minute
1㎜ amplitude at frequency of 10 to 55㎐ in each of X, Y, Z directions for 2 hours
500㎨(50G) in X, Y, Z directions for 3 times
Operating indicator(Red LED)
-25 to 70℃, Storage: -30 to 80℃
Ambient
humidity
35 to 95%RH, Storage: 35 to 95%RH
Protection circuit
Protection
Materials
Approval
Unit Weight
Surge protection
IP67(IEC standards)
Case: Heat-resistant ABS, Standard cable(Black): Polyvinyl chloride(PVC).
Approx. 65g
Approx. 106g
Approx. 152g
※ Environment resistance is rated at no freezing or condensation.
▣ Dimensions
PSN25 / PSN30 / PSN40
B
C
A
B
A DC
E
F
LED
※H
G 2000
D
E
F
G
H
※"H" type : ø4, 2 cores(Conductor cross section: 0.3㎟, Insulator diameter:ø1.25)
PSN25
PSN30
(Unit:mm)
PSN40
25 30 40
35.5
48.5
47
ø4.2
ø4.5
ø5.5
18 22 30
25.3 30
40
16.8 20
25
39 53 53
444
◎Bracket
PSN25
32
2-M4 TAP 3.5
PSN30
34
2-M4 TAP 3.5
PSN40
2-M5 TAP 6
35
17.5
11.8
17.8
14
19.5
15.5
▣ Mutual-interference & Influence by surrounding metals
◎Mutual-interference
When several proximity sensors are mounted closely, malfunction of sensor may be caused due to mutual interference.
Therefore, be sure to keep a minimum distance between the two sensors as below chart.
Face to Face
Parallel
A
B
m
d
C
m
◎Influence by surrounding metals
When sensors are mounted on metallic panel, it is required to protect the sensors from malfunction by any metallic object.
Therefore, be sure to keep a minimum distance as below chart.
(Unit:mm)
Item
Model
PSN25
10㎜
PSN30
15㎜
PSN40
A 30 60 90 120
B 40 50 65 70
C5 5 5 5
d 15 30 45 60
ℓ 25 30 45 45
m 20 25 35 35
▣ Setting distance
Target
Target
Moving
direction
Moving
direction
Sa Sn
{
Sn:Sensing distance
Sa:Setting distance
(70% of Sn)
(a) (b)
Sensing distance can be changed by the shape, size or material of the target.
Therefore please check the sensing distance like (a), then pass the target
within range of setting distance(Sa) like (b).
Setting distance(Sa)
= Sensing distance(Sn) × 70%
Ex)PSN30-10AO
Setting distance(Sa) = 10mm × 0.7 = 7mm
▣ Caution for using
1. This equipment shall not be used outdoors or beyond specified temperature range.
2. Do not apply over tensile strength of cord. (ø4: max. 30N)
3. Do not use the same conduit with cord of this unit and electric power line or power line.
4. Tighten strength of installing screws should be under 10kgf.cm.
5. Please check the voltage changes of power source in order not to excess the rated power input.
6. Do not connect directly output terminal to capacitive load.
7. Please make wire as short as possible in order to avoid noise.
8. Be sure to use cable as indicated specification on this product. If wrong cable or bended cable is used, it shall not maintain the water-proof.
9. It is possible to extend cable with over 0.3mm2 and max. 200m.
10. If the target is plated, the operating distance can be changed by the plating material.
11. It may cause malfunction by metal particle on product.
12. If there are machines(motor, welding, etc.), which occurs big surge around this unit, please install the varistor or absorber to source
of surge, even though there is built-in surge absorber in this unit.
13. If connecting the load with big inrush current(AC type bulb, motor, etc.) to this unit, the big inrush current will flow because the
initial resistance is low. If the current flows, the resistance of load will be bigger, then it will return to standard current. In this case,
proximity sensor might be damaged by inrush current.
If you use AC type bulb, please connect extra relay or resistance in order to protect proximity sensor from.
14. If making a transceiver close to proximity sensor or wire connection, it may cause malfunction.
15. In case of the load current is small: When the load current is under 5mA, make the residual voltage is less than return voltage to
connect the bleeder resistor to load in parallel.
※110VAC 50/60Hz: 20㏀, Min. 3W, 220VAC 50/60Hz: 39㏀ Min. 5W
Load
Vs:Power supply, Io:Min.operating current for
proximity sensor, Ioff:Return current of load,
P:Resistance W of Bleeder resistor
※R≤
Vs
Io-Ioff
(㏀)
Vs²
P> R (mW)
Proximity
sensor
+
Bleeder resistor(R) -
※It may cause malfunction if above instructions are not followed.
▣ Major products
■ Proximity sensors
■ Counters
■ Area sensors
■ Timers
■ Photoelectric sensors
■ Display units
■ Fiber optic sensors
■ Panel meters
■ Door/Door side sensors
■ Pressure sensors
■ Sensor controllers
■ Rotary encoders
■ Graphic/Logic panels
■ Power controllers
■ Temperature controllers
■ Tachometer/Pulse(Rate) meters
■ Temperature/Humidity transducers
■ Switching power supplies
■ Stepping motors/drivers/motion controllers
■ Field network devices
■ Laser marking system(CO₂, Nd:YAG)
■ Laser welding/soldering system
http://www.autonics.com
Satisfiable Partner For Factory Automation
■HEAD QUARTERS :
41-5. Yongdang-dong, Yangsan-si, Gyeongnam, 626-847,
Korea
■OVERSEAS SALES :
Bldg. 402 3rd FL., Bucheon Techno Park, 193, Yakdae-dong,
Wonmi-gu, Bucheon-si, Gyeonggi-do, 420-734, Korea
TEL : 82-32-610-2730 / FAX : 82-32-329-0728
■E-mail : [email protected]
The proposal of a product improvement
and development :[email protected]
EP-KE-07-0280F


Part Details

On this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for PSN25-5AO electronic component.


Information Total 1 Pages
Link URL [ Copy URL to Clipboard ]
Download [ PSN25-5AO.PDF Datasheet ]

Share Link :

Electronic Components Distributor


An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists.


SparkFun Electronics Allied Electronics DigiKey Electronics Arrow Electronics
Mouser Electronics Adafruit Newark Chip One Stop


Featured Datasheets

Part NumberDescriptionMFRS
PSN25-5ACThe function is INDUCTIVE PROXIMITY SENSOR. AutonicsAutonics
PSN25-5AOThe function is INDUCTIVE PROXIMITY SENSOR. AutonicsAutonics

Semiconductors commonly used in industry:

1N4148   |   BAW56   |   1N5400   |   NE555   |  

LM324   |   BC327   |   IRF840  |   2N3904   |  



Quick jump to:

PSN2     1N4     2N2     2SA     2SC     74H     BC     HCF     IRF     KA    

LA     LM     MC     NE     ST     STK     TDA     TL     UA    



Privacy Policy   |    Contact Us     |    New    |    Search