DataSheet39.com

What is B121EW01-V5?

This electronic component, produced by the manufacturer "AUO", performs the same function as "LCD MODULE".


B121EW01-V5 Datasheet PDF - AUO

Part Number B121EW01-V5
Description LCD MODULE
Manufacturers AUO 
Logo AUO Logo 


There is a preview and B121EW01-V5 download ( pdf file ) link at the bottom of this page.





Total 36 Pages



Preview 1 page

No Preview Available ! B121EW01-V5 datasheet, circuit

www.DataSheet4U.net
Product Specification
B121EW01 V5
AU OPTRONICS CORPORATION
Product Specification
12.1WXGA Color TFT-LCD Module
Model Name: B121EW01 V5
Approved by
Joselyn Liu
Prepared by
Kay Liu
MDBU Marketing Division / AU Optronics corporation
Customer
Checked & Approved by
Document version 0.1
1/36

line_dark_gray
B121EW01-V5 equivalent
www.DataSheet4U.net
Product Specification
B121EW01 V5
1. Handling Precautions
1) Since front polarizer is easily damaged, pay attention not to scratch it.
2) Be sure to turn off power supply when inserting or disconnecting from input connector.
3) Wipe off water drop immediately. Long contact with water may cause discoloration or
spots.
4) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.
5) Since the panel is made of glass, it may break or crack if dropped or bumped on hard
surface.
6) Since CMOS LSI is used in this module, take care of static electricity and insure
human earth when handling.
7) Do not open nor modify the Module Assembly.
8) Do not press the reflector sheet at the back of the module to any directions.
9) In case if a Module has to be put back into the packing container slot after once it was
taken out from the container, do not press the center of the CCFL Reflector edge.
Instead, press at the far ends of the CFL Reflector edge softly. Otherwise the TFT
Module may be damaged.
10)At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor
tilt the Interface Connector of the TFT Module.
11) After installation of the TFT Module into an enclosure (Notebook PC Bezel, for
example), do not twist nor bend the TFT Module even momentary. At designing the
enclosure, it should be taken into consideration that no bending/twisting forces are
applied to the TFT Module from outside. Otherwise the TFT Module may be
damaged.
12)Cold cathode fluorescent lamp in LCD contains a small amount of mercury. Please follow
local ordinances or regulations for disposal.
13)Small amount of materials having no flammability grade is used in the LCD module. The
LCD module should be supplied by power complied with requirements of Limited Power
Source(, IEC60950 or UL1950), or be applied exemption.
14)The LCD module is designed so that the CFL in it is supplied by Limited Current
Circuit(IEC60950 or UL1950). Do not connect the CFL in Hazardous Voltage Circuit.
Document version 0.1
5/36


line_dark_gray

Preview 5 Page


Part Details

On this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for B121EW01-V5 electronic component.


Information Total 36 Pages
Link URL [ Copy URL to Clipboard ]
Download [ B121EW01-V5.PDF Datasheet ]

Share Link :

Electronic Components Distributor


An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists.


SparkFun Electronics Allied Electronics DigiKey Electronics Arrow Electronics
Mouser Electronics Adafruit Newark Chip One Stop


Featured Datasheets

Part NumberDescriptionMFRS
B121EW01-V0The function is LCD MODULE. AUOAUO
B121EW01-V2The function is LCD MODULE. AUOAUO
B121EW01-V3The function is LCD MODULE. AUOAUO

Semiconductors commonly used in industry:

1N4148   |   BAW56   |   1N5400   |   NE555   |  

LM324   |   BC327   |   IRF840  |   2N3904   |  



Quick jump to:

B121     1N4     2N2     2SA     2SC     74H     BC     HCF     IRF     KA    

LA     LM     MC     NE     ST     STK     TDA     TL     UA    



Privacy Policy   |    Contact Us     |    New    |    Search