DataSheet39.com

What is MIC3839?

This electronic component, produced by the manufacturer "Micrel Semiconductor", performs the same function as "(MIC3838 / MIC3839) Flexible Push-Pull PWM Controller".


MIC3839 Datasheet PDF - Micrel Semiconductor

Part Number MIC3839
Description (MIC3838 / MIC3839) Flexible Push-Pull PWM Controller
Manufacturers Micrel Semiconductor 
Logo Micrel Semiconductor Logo 


There is a preview and MIC3839 download ( pdf file ) link at the bottom of this page.





Total 11 Pages



Preview 1 page

No Preview Available ! MIC3839 datasheet, circuit

MIC3838/3839
Micrel
MIC3838/3839
Flexible Push-Pull PWM Controller
General Description
The MIC3838 and MIC3839 are a family of complementary
output push-pull PWM control ICs that feature high speed and
low power consumption. The MIC3838/9 are ideal for telecom
level (36V to 75V) isolated step down dc/dc conversion
applications where high output current, small size, and high
efficiency are required
The MIC3838/9 are designed for high flexibility with minimum
pin-count. The devices are easily configurable for either
voltage-mode or current-mode control. Additionally, the
MIC3838/9 can easily implement a volt-second clamp that
automatically limits the duty cycle during input transients,
allowing designers to use the smallest possible transformers
and power components. A 3V reference output is also avail-
able that eliminates the need for an external reference.
The dual-ended push-pull architecture of the MIC3838/9
allows more efficient utilization of the transformer than single-
ended topologies, allowing smaller size dc/dc solutions.
Additionally, the out-of-phase push-pull topology allows a
higher effective duty cycle, reducing input and output ripple
as well as stress on the external components. The dead-time
between the two outputs is adjustable between 60ns to
200ns, limiting the duty cycle of each output stage to less than
50%.
The MIC3838 has a turn-on threshold of 12.5V whereas the
MIC3839 has a lower turn-on threshold of 4.3V. Both devices
are available in a small size MSOP-10 package with an
operating range of –40°C to +85°C.
Data sheets and support documentation can be found on
Micrel’s web site at www.micrel.com.
Typical Application
VIN
36V to 75V
Start-Up
Circuitry
Features
• Dual output drive stages in push-pull configuration
• Configurable for current-mode or voltage-mode control
• Easily implements volt-second clamp
• Leading edge current-sense blanking
• 3V reference output available
• 130µA typical start-up current
• 1mA typical run current
• Operation to 1MHz
• On-chip error amplifier with 4MHz gain bandwidth
product
• Internal soft start
• On-chip VDD clamping
• Output drive stages capable of 500mA peak source
current, 1A peak sink current
Applications
• High efficiency “brick” power supply modules
• Half bridge converters
• Full bridge converters
• Push-pull converters
• Voltage-fed push-pull converters
• Telecom equipment and power supplies
• Industrial power supplies
• 42V automotive power supplies
• Base stations
• Networking power supplies
VOUT
12V 100W
MIC3838x-x
VREF VDD
RC OUTA
GND OUTB
COMP RAMP
FB ILIM
Feed Forward
Ramp/
Volt Sec Clamp
Reference
& Isolation
Voltage-Mode Half-Bridge Converter CIrcuit
Micrel, Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel + 1 (408) 944-0800 • fax + 1 (408) 474-1000 • http://www.micrel.com
April 2005
1 MIC3838/3839

line_dark_gray
MIC3839 equivalent
MIC3838/3839
Micrel
Parameter
Condition
Min Typ Max Units
Undervoltage Lockout Section
Start Threshold
MIC3838, Note 11
11.5 12.5 13.5
V
MIC3839
4.1 4.3 4.5
V
Minimum Operating Voltage
MIC3838
7.6 8.3
9
V
After Start
MIC3839
3.9 4.1 4.3
V
Hysteresis
MIC3838
3.5 4.2 5.1
V
MIC3839
0.1 0.2 0.3
V
Soft Start Section
COMP Rise Time
FB = 1.8V, Rise from 0.5V to 3V
2.5 20 ms
Overall Section
Startup Current
Operating Supply Current
VDD Zener Shunt Voltage
VDD < Start Threshold (MIC3839)
FB = 0V, Ramp = ILIM = 0V, Notes 11, 12
IDD = 10mA, Note 13
130 260
µA
1.5 2 mA
13 14 15
V
Note 1. Exceeding the absolute maximum rating may damage the device.
Note 2. The device is not guaranteed to function outside its operating rating.
Note 3. Devices are ESD sensitive. Handling precautions recommended. Human body model, 1.5k in series with 100pF.
Note 4.
Note 5.
Maximum operating voltage is equal to the VDD (zener) shunt voltage. When operating at or near the shunt voltage, care must be taken to limit
the VDD pin current less than the 20mA VDD maximum current rating.
Specification for packaged product only.
Note 6. Measured at RC.
Note 7. COMP pin is internally clamped to 3.65V(typ.). COMP pin source current is measured at VCOMP = 3.0V to avoid interferring with clamp.
Minimum source current is higher as VCOMP approaches VCLAMP.
VCOMP
Note 8. Gain is defined by A = VCS , 0 VCS 0.4V.
Note 9. Parameter measured at trip point of latch with FB at 0V
Note 10. The internal current sink on the Ramp and ILIM pin are designed to discharge an external filter capacitor. It is not intended to be a DC sink
path. Internal discharge FET should be able to discharge the Volt-Sec clamp and feed-forward circuits in the figure below within 50ns.
Note 11. For MIC3838, set VDD above the start threshold before setting at 10V.
Note 12. Does not include current in the external oscillator network.
Note 13. Start threshold and Zener Shunt threshold track one another.
April 2005
5 MIC3838/3839


line_dark_gray

Preview 5 Page


Part Details

On this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for MIC3839 electronic component.


Information Total 11 Pages
Link URL [ Copy URL to Clipboard ]
Download [ MIC3839.PDF Datasheet ]

Share Link :

Electronic Components Distributor


An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists.


SparkFun Electronics Allied Electronics DigiKey Electronics Arrow Electronics
Mouser Electronics Adafruit Newark Chip One Stop


Featured Datasheets

Part NumberDescriptionMFRS
MIC38300The function is 3A High-Efficiency Low Dropout Regulator. Micrel SemiconductorMicrel Semiconductor
MIC3832The function is (MIC3832 / MIC3833) Current-Fed PWM Controllers. Micrel SemiconductorMicrel Semiconductor
MIC3833The function is (MIC3832 / MIC3833) Current-Fed PWM Controllers. Micrel SemiconductorMicrel Semiconductor

Semiconductors commonly used in industry:

1N4148   |   BAW56   |   1N5400   |   NE555   |  

LM324   |   BC327   |   IRF840  |   2N3904   |  



Quick jump to:

MIC3     1N4     2N2     2SA     2SC     74H     BC     HCF     IRF     KA    

LA     LM     MC     NE     ST     STK     TDA     TL     UA    



Privacy Policy   |    Contact Us     |    New    |    Search