ST6225L Datasheet PDF - ST Microelectronics
|(ST6215L / ST6225L) LOW VOLTAGE 8-BIT ROM MCUs WITH A/D CONVERTER AND 28 PINS
There is a preview and ST6225L download ( pdf file ) link at the bottom of this page.
Total 10 Pages
Preview 1 page
No Preview Available !
LOW VOLTAGE 8-BIT ROM MCUs WITH
A/D CONVERTER AND 28 PINS
s 2.4 to 3.9V Supply Operating Range
s 4 MHz Maximum Clock Frequency
s 0 to +70°C Operating Temperature Range
s Run, Wait and Stop Modes
s 5 Interrupt Vectors
s Look-up Table capability in Program Memory
s Data Storage in Program Memory:
User selectable size
s Data RAM: 64bytes
s 20 I/O pins, fully programmable as:
– Input with pull-up resistor
– Input without pull-up resistor
– Input with interrupt generation
– Open-drain or push-pull output
– Analog Input
s 8 I/O lines can sink up to 12mA to drive LEDs
s 8-bit Timer/ Counter with 7-bit programmable
s Digital Watchdog
s 8-bit A/D Converter with 16 analog inputs
s On-chip Clock oscillator can be driven by Quartz
Crystal Ceramic resonator or RC network
s Power-on Reset
s One external Non-Maskable Interrupt
s ST626x-EMU2 Emulation and Development
System (connects to an MS-DOS PC via an
RS232 serial line)
2 ELECTRICAL CHARACTERISTICS
2.1 ABSOLUTE MAXIMUM RATINGS
This product contains devices to protect the inputs
against damage due to high static voltages, how-
ever it is advisable to take normal precaution to
avoid application of any voltage higher than the
specified maximum rated voltages.
For proper operation it is recommended that VI
and VO be higher than VSS and lower than VDD.
Reliability is enhanced if unused inputs are con-
nected to an appropriate logic voltage level (VDD
Power Considerations.The average chip-junc-
tion temperature, Tj, in Celsius can be obtained
Tj=TA + PD x RthJA
Where:TA = Ambient Temperature.
RthJA =Package thermal resistance (junc-
PD = Pint + Pport.
Pint =IDD x VDD (chip internal power).
Pport =Port power dissipation (determined
by the user).
Current Drain per Pin Excluding VDD, VSS
Total Current into VDD (source)
Total Current out of VSS (sink)
-0.3 to 7.0
VSS - 0.3 to VDD + 0.3(1)
VSS - 0.3 to VDD + 0.3(1)
-60 to 150
- Stresses above those listed as “absolute maximum ratings” may cause permanent damage to the device. This is a stress rating only and
functional operation of the device at these conditions is not implied. Exposure to maximum rating conditions for extended period s may
affect device reliability.
- (1) Within these limits , clamping diodes are guarantee to be not conductive. Voltages outside these limits are authorised as long as injection
current is kept within the specification.
Preview 5 Page
On this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for ST6225L electronic component.
|Total 10 Pages
|[ Copy URL to Clipboard ]
|[ ST6225L.PDF Datasheet ]
Share Link :
Electronic Components Distributor
An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists.
|Chip One Stop
|The function is 8-BIT MCUs. ST Microelectronics
|The function is 8-BIT MCU. ST Microelectronics
|The function is (ST6215L / ST6225L) LOW VOLTAGE 8-BIT ROM MCUs WITH A/D CONVERTER AND 28 PINS. ST Microelectronics
Semiconductors commonly used in industry:
Quick jump to: