DataSheet39.com

What is CR0720SC?

This electronic component, produced by the manufacturer "Littelfuse", performs the same function as "The CR range of protectors are based on the proven technology of the T10 thyristor product".


CR0720SC Datasheet PDF - Littelfuse

Part Number CR0720SC
Description The CR range of protectors are based on the proven technology of the T10 thyristor product
Manufacturers Littelfuse 
Logo Littelfuse Logo 


There is a preview and CR0720SC download ( pdf file ) link at the bottom of this page.





Total 3 Pages



Preview 1 page

No Preview Available ! CR0720SC datasheet, circuit

CRxxxx series
Description
The CR range of protectors are based on the proven
technology of the T10 thyristor product. Designed for
transient voltage protection of telecommunications
equipment, it provides higher power handling than a
conventional avalanche diode (TVS) and when compared to
a GDT offers lower voltage clamping levels and infinite surge
life.
Packaged in a transfer molded DO-214AA surface mount
outline designed for high speed pick & place machines used
in today’s surface mount assembly lines.
Electrical Charecteristics
The electrical characteristics of a CRXXXX device is similar
to that of a self gated Triac, but the CR is a two terminal
device with no gate. The gate function is achieved by an
internal current controlled mechanism.
Like the T.T.S. diodes, the CRXXXX has a standoff voltage
(Vrm) which should be equal to or greater than the operating
voltage of the system to be protected. At this voltage (Vrm)
the current consumption of the CRXXXX is negligible and will
not effect the protected system.
When a transient occurs, the voltage across the CRXXXX
will increase until the breakdown voltage (Vbr) is reached. At
this point the device will operate in a similar way to a T.V.S.
device and is in an avalanche mode.
The voltage of the transient will now be limited and will only
increase by a few volts as the device diverts more current.
As this transient current rises, a level of current through the
device is reached (Ibo) which causes the device to switch to
a fully conductive state such that the voltage across the
device is now only a few volts (Vt). The voltage at which the
device switches from the avalanche mode to the fully
conductive state (Vt) is known as the Breakover Voltage
(Vbo). When the device is in the Vt state, high currents can
be deverted without damage to the CRXXXX due to the low
voltage across the device, since the limiting factor in such
devices is dissipated power (V x I).
Resetting of the device to the non conducting state is
controlled by the current flowing through the device. When
the current falls below a certain value, known as the Holding
Current (Ih), the device resets automatically.
As with the avalanche T.V.S. device, if the CRXXXX is
subjected to a surge current which is beyond its maximum
rating, then the device will fail in short circuit mode, this
ensures that the equipment is ultimately protected.
Selecting A CRXXXX
1. When selecting a CRXXXX device, it is important that the
Vrm of the device is equal to or greater than the operating
voltage of the system.
2. The minimum Holding Current (Ih) must be greater than
the current the system is capable of delivering otherwise the
device will remain conducting following a transient condition.
IT
IH
VT
IRM
IBO
VBR
VRM VBO
MIN
V-I Graph
Illustrating Symbols
and Terms for
the CR Surge
Protection Device.
The CRXXXX Range Can Be Used to Protect Against Surges As Defined In The Following International Standards.
SA SB SC
FCC Rules Part 68/D
Metallic
Longitudinal
10/560µs
10/160µs
50A
100A
100A
150A
100A
200A
Bellcore Specification
TR-NWT-001089
10/1000µs
2/10µs
100v/µs
37A
-
1KV
75A 100A
- 500A
1KV 1KV
ITU K-17 (Formerly CCITT)
Voltage Wave Form
Current Wave Form
100/700µs
5/310µs
-
-
1.5KV
38A
1.5KV
38A
VDE 0433
Voltage Wave Form
Current Wave Form
10/700µs
5/310µs
-
-
2KV 4.0KV
50A 100A
C-NET 131-24
Voltage Wave From
Current Wave Form
0.5/700µs
0.8/310µs
1.0KV
25A
1.0KV
25A
4.0KV
100A
IEC 1000-4-5
(Discharge through 2impendance) I
Voltage Wave Form
8/20µs
1-2/50µs
-
-
100A
300V
250A
500V
ITU K-20
(Formerly CCITT)
Voltage Wave Form
Current Wave Form
10/700µs
5/310µs
1000V
25A
10000V
25A
4000V
100A
52 w w w . l i t t e l f u s e . c o m


Part Details

On this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for CR0720SC electronic component.


Information Total 3 Pages
Link URL [ Copy URL to Clipboard ]
Download [ CR0720SC.PDF Datasheet ]

Share Link :

Electronic Components Distributor


An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists.


SparkFun Electronics Allied Electronics DigiKey Electronics Arrow Electronics
Mouser Electronics Adafruit Newark Chip One Stop


Featured Datasheets

Part NumberDescriptionMFRS
CR0720SAThe function is The CR range of protectors are based on the proven technology of the T10 thyristor product. LittelfuseLittelfuse
CR0720SBThe function is The CR range of protectors are based on the proven technology of the T10 thyristor product. LittelfuseLittelfuse
CR0720SCThe function is The CR range of protectors are based on the proven technology of the T10 thyristor product. LittelfuseLittelfuse

Semiconductors commonly used in industry:

1N4148   |   BAW56   |   1N5400   |   NE555   |  

LM324   |   BC327   |   IRF840  |   2N3904   |  



Quick jump to:

CR07     1N4     2N2     2SA     2SC     74H     BC     HCF     IRF     KA    

LA     LM     MC     NE     ST     STK     TDA     TL     UA    



Privacy Policy   |    Contact Us     |    New    |    Search