|
|
PDF VN7016AJ Data sheet ( Hoja de datos )
| Número de pieza | VN7016AJ | |
| Descripción | high-side driver | |
| Fabricantes | STMicroelectronics | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de VN7016AJ (archivo pdf) en la parte inferior de esta página. Total 30 Páginas | ||
|
No Preview Available !
VN7016AJ
High-side driver with MultiSense analog feedback for automotive
applications
Datasheet - target specification
− Loss of ground and loss of VCC
− Reverse battery with external
components
− Electrostatic discharge protection
Features
Max transient supply voltage
Operating voltage range
Typ. on-state resistance (per Ch)
Current limitation (typ)
Standby current (max)
VCC 40 V
VCC 4 to 28 V
RON 16 mΩ
ILIMH 77 A
ISTBY 0.5 µA
• Automotive qualified
• General
− Single channel smart high-side driver
with MultiSense analog feedback
− Very low standby current
− Compatible with 3 V and 5 V CMOS
outputs
• MultiSense diagnostic functions
− Multiplexed analog feedback of: load
current with high precision proportional
current mirror, VCC supply voltage and
TCHIP device temperature
− Overload and short to ground (power
limitation) indication
− Thermal shutdown indication
− OFF-state open-load detection
− Output short to VCC detection
− Sense enable/disable
• Protections
− Undervoltage shutdown
− Overvoltage clamp
− Load current limitation
− Self limiting of fast thermal transients
− Configurable latch-off on
overtemperature or power limitation
with dedicated fault reset pin
Applications
• All types of Automotive resistive, inductive
and capacitive loads
• Specially intended for Automotive
Headlamps
Description
The device is a single channel high-side driver
manufactured using ST proprietary VIPower® M0-
7 technology and housed in PowerSSO-16
package. The device is designed to drive 12 V
automotive grounded loads through a 3 V and
5 V CMOS-compatible interface, providing
protection and diagnostics.
The device integrates advanced protective
functions such as load current limitation, overload
active management by power limitation and
overtemperature shutdown with configurable
latch-off.
A FaultRST pin unlatches the output in case of
fault or disables the latch-off functionality.
A dedicated multifunction multiplexed analog
output pin delivers sophisticated diagnostic
functions including high precision proportional
load current sense, supply voltage feedback and
chip temperature sense, in addition to the
detection of overload and short circuit to ground,
short to VCC and OFF-state open-load.
A sense enable pin allows OFF-state diagnosis to
be disabled during the module low-power mode
as well as external sense resistor sharing among
similar devices.
May 2015
DocID027399 Rev 1
1/45
This is preliminary information on a new product foreseen to be
developed. Details are subject to change without notice.
www.st.com
1 page  
VN7016AJ
Block diagram and pin description
1 Block diagram and pin description
Figure 1: Block diagram
VCC
VCC – GND
Clamp
Internal supply
Undervoltage
shut-down
FaultRST
Con trol & Diagnostic
VCC – OUT
Clamp
INPUT
SEL1
SEL0
SEn
MultiSense
GND
VCC
T
Fault
VSENSEH
Gate Driver
Current
Limitation
VON
Limitation
Power Limitation
Overtemperature
Short to VCC
Open-Load in OFF
Current
Sense
T
OUTPUT
GAPGCFT00328
Table 1: Pin functions
Name
Function
VCC Battery connection.
OUTPUT Power outputs. All the pins must be connected together.
GND
Ground connection. Must be reverse battery protected by an external diode / resistor
network.
INPUT
Voltage controlled input pin with hysteresis, compatible with 3 V and 5 V CMOS outputs.
It controls output switch state.
MultiSense
Multiplexed analog sense output pin; it delivers a current proportional to the selected
diagnostic: load current, supply voltage or chip temperature.
SEn
Active high compatible with 3 V and 5 V CMOS outputs pin; it enables the MultiSense
diagnostic pin.
SEL0,1
Active high compatible with 3 V and 5 V CMOS outputs pin; they address the MultiSense
multiplexer.
FaultRST
Active low compatible with 3 V and 5 V CMOS outputs pin; it unlatches the output in case
of fault; If kept low, sets the outputs in auto-restart. mode
DocID027399 Rev 1
5/45
5 Page 
VN7016AJ
7 V < VCC < 18 V; -40°C < Tj < 150°C
Table 8: Protections
Electrical specification
Symbol
Parameter
Test conditions
Min. Typ. Max. Unit
ILIMH
ILIML
TTSD
TR
TRS
DC short circuit current
Short circuit current
during thermal cycling
Shutdown temperature
Reset temperature(1)
Thermal reset of fault
diagnostic indication
VCC = 13 V
4 V < VCC < 18 V (1)
VCC = 13 V;
TR < Tj < TTSD
VFR = 0 V; VSEn = 5 V
55 77
110
A
32
150 175
TRS + 1 TRS + 7
200
135 °C
THYST
ΔTJ_SD
Thermal hysteresis
(TTSD - TR)(1)
Dynamic temperature
tLATCH_RST
Fault reset time for
output unlatch(1)
Tj = -40°C; VCC = 13 V
VFR = 5 V to 0 V; VSEn = 5 V;
VIN = 5 V; VSEL0 = 0 V;
VSEL1 = 0 V
3
7
60 K
10 20 µs
VDEMAG
Turn-off output voltage
clamp
VON
Output voltage
droplimitation
IOUT = 2 A; L = 6 mH;
Tj = -40°C
IOUT = 2 A; L = 6 mH;
Tj = 25°C to 150°C
IOUT = 0.6 A
VCC - 38
V
VCC - 41 VCC - 46 VCC - 52 V
20 mV
Notes:
(1)Parameter guaranteed by design and characterization; not subject to production test.
Table 9: MultiSense
7 V < VCC < 18 V; -40°C < Tj < 150°C
Symbol
VSENSE_CL
Parameter
Test conditions
VSEn = 0 V; ISENSE = 1 mA
MultiSense clamp voltage
VSEn = 0 V; ISENSE = -1 mA
CurrentSense characteristics
K0 IOUT/ISENSE
IOUT = 0.6 A; VSENSE = 0.5 V;
VSEn = 5 V
dK0/K0(1)(2)
Current sense ratio drift
IOUT = 0.6 A; VSENSE = 0.5 V;
VSEn = 5 V
K1 IOUT/ISENSE
IOUT = 1 A; VSENSE = 4 V;
VSEn = 5 V
dK1/K1(1)(2)
Current sense ratio drift
IOUT = 1 A; VSENSE = 4 V;
VSEn = 5 V
K2 IOUT/ISENSE
IOUT = 4 A; VSENSE = 4 V;
VSEn = 5 V
dK2/K2(1)(2)
Current sense ratio drift
IOUT = 4 A; VSENSE = 4 V;
VSEn = 5 V
Min. Typ. Max. Unit
-17 -12
V
7
2370 3900 5540
-20 20 %
2560 3640 4760
-15 15 %
2770 3440 4170
-10 10 %
DocID027399 Rev 1
11/45
11 Page | ||
| Páginas | Total 30 Páginas | |
| PDF Descargar | [ Datasheet VN7016AJ.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| VN7016AJ | high-side driver | STMicroelectronics |
| VN7016AJ-E | High-side driver | STMicroelectronics |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |