VN7007AH Datasheet PDF - STMicroelectronics
Part Number | VN7007AH | |
Description | high-side driver | |
Manufacturers | STMicroelectronics | |
Logo | ||
There is a preview and VN7007AH download ( pdf file ) link at the bottom of this page. Total 30 Pages |
Preview 1 page No Preview Available ! VN7007AH
High-side driver with CurrentSense analog feedback for
automotive applications
Datasheet - production data
Features
Max transient supply voltage
Operating voltage range
Typ. on-state resistance (per Ch)
Current limitation (typ)
Stand-by current (max)
VCC 40 V
VCC 4 to 28 V
RON 7 mΩ
ILIMH 100 A
ISTBY 0.5 µA
• Automotive qualified
• General
− Single channel smart high-side driver
with CurrentSense analog feedback
− Very low standby current
− Compatible with 3.0 V and 5 V CMOS
outputs
• Diagnostic functions
− Overload and short to ground (power
limitation) indication
− Thermal shutdown indication
− OFF-state open-load detection
− Output short to VCC detection
− Sense enable/ disable
• Protections
− Undervoltage shutdown
− Overvoltage clamp
− Load current limitation
− Self limiting of fast thermal transients
− Loss of ground and loss of VCC
− Reverse battery
− Electrostatic discharge protection
Applications
• All types of Automotive resistive, inductive
and capacitive loads
• Specially intended for Automotive
Headlamps
Description
The device is a single channel high-side driver
manufactured using ST proprietary VIPower®
technology and housed in the Octapak package.
The device is designed to drive 12 V automotive
grounded loads through a 3 V and 5 V CMOS-
compatible interface, providing protection and
diagnostics.
The device integrates advanced protective
functions such as load current limitation, overload
active management by power limitation and
overtemperature shutdown.
A sense enable pin allows OFF-state diagnosis to
be disabled during the module low-power mode
as well as external sense resistor sharing among
similar devices.
Table 1: Device summary
Package
Order codes
Tape and reel
Octapak
VN7007AHTR
October 2015
DocID027957 Rev 2
This is information on a product in full production.
1/37
www.st.com
|
|
VN7007AH
Block diagram and pin description
1 Block diagram and pin description
Figure 1: Block diagram
Signal Clamp
Undervoltage
Control& Diagnostic
Power
Clamp
Reverse
Battery
Protection
VCC
IN DRIVER
SEn
Over
temperature
V SENSEH
Current
Limitation
VON
Li mitation
OFF State
Open load
CS Current
Sense
LOGIC
OVERLOAD PROTECTION
( ACTIVE POWER LIMI TATION )
OUT
Name
VCC
OUTPUT
GND
INPUT
CS
SEn
GND
GAPGCFT00664
Table 2: Pin functions
Function
Battery connection.
Power outputs. All the pins must be connected together.
Ground connection.
Voltage controlled input pin with hysteresis. Compatible with 3 V and 5 V
CMOS outputs. It controls output switch state.
Analog current sense output pin delivers a current proportional to the load
current.
Active high compatible with 3 V and 5 V CMOS outputs pin; it enables the
CurrentSense diagnostic pin.
DocID027957 Rev 2
5/37
Preview 5 Page |
Part DetailsOn this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for VN7007AH electronic component. |
Information | Total 30 Pages | |
Link URL | [ Copy URL to Clipboard ] | |
Download | [ VN7007AH.PDF Datasheet ] |
Share Link :
Electronic Components Distributor
An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists. |
SparkFun Electronics | Allied Electronics | DigiKey Electronics | Arrow Electronics |
Mouser Electronics | Adafruit | Newark | Chip One Stop |
Featured Datasheets
Part Number | Description | MFRS |
VN7007AH | The function is high-side driver. STMicroelectronics | |
VN7007ALH | The function is high-side driver. STMicroelectronics | |
Semiconductors commonly used in industry:
1N4148 |  
BAW56 |
1N5400 |
NE555 | | ||
Quick jump to:
VN70
1N4
2N2
2SA
2SC
74H
BC
HCF
IRF
KA |