|
|
Número de pieza | VND7140AJ12 | |
Descripción | Double channel high-side driver | |
Fabricantes | STMicroelectronics | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de VND7140AJ12 (archivo pdf) en la parte inferior de esta página. Total 30 Páginas | ||
No Preview Available ! VND7140AJ12
Double channel high-side driver with CurrentSense analog
feedback for automotive applications
Datasheet - production data
PowerSSO-12
GAPG040515 1112CFT
Features
Max transient supply voltage VCC
40 V
Operating voltage range
VCC 4 V to 28 V
Minimum cranking supply
voltage (VCC decreasing)
VUSD_Cranking
2.85 V
Typ. on-state resistance
(per Ch)
RON 140 mΩ
Current limitation (typ)
ILIMH
12 A
Standby current (max)
ISTBY
0.5 µA
• Automotive qualified
• Extreme low voltage operation for deep cold
cranking applications (compliant with LV124,
revision 2013)
• General
− Double channel smart high-side driver
with CurrentSense analog feedback
− Very low standby current
− Compatible with 3 V and 5 V CMOS
outputs
• CurrentSense diagnostic functions
− Multiplexed analog feedback of: load
current with high precision proportional
current mirror
− Overload and short to ground (power
limitation) indication
− Thermal shutdown indication
− Off-state open-load detection
− Output short to VCC detection
− Sense enable/ disable
• Protections
− Undervoltage shutdown
− Overvoltage clamp
− Load current limitation
− Self limiting of fast thermal transients
− Loss of ground and loss of VCC
− Reverse battery with external
components
− Electrostatic discharge protection
Applications
• All types of automotive resistive, inductive
and capacitive loads
• Specially intended for automotive signal
lamps (up to R10W or LED Rear
Combinations)
Description
The device is a double channel high-side driver
manufactured using ST proprietary VIPower®
technology and housed in PowerSSO-12
package. The device is designed to drive 12 V
automotive grounded loads through a 3 V and
5 V CMOS compatible interface, providing
protection and diagnostics.
The device integrates advanced protective
functions such as load current limitation, overload
active management by power limitation and
overtemperature shutdown.
A current sense delivers high precision
proportional load current sense in addition to the
detection of overload and short circuit to ground,
short to VCC and off-state open-load.
A sense enable pin allows off-state diagnosis to
be disabled during the module low-power mode
as well as external sense resistor sharing among
similar devices.
September 2015
DocID027923 Rev 3
This is information on a product in full production.
1/43
www.st.com
1 page VND7140AJ12
Block diagram and pin description
1 Block diagram and pin description
Figure 1: Block diagram
Table 1: Pin functions
Name
Function
VCC Battery connection.
OUTPUT0,1 Power output.
GND
Ground connection. Must be reverse battery protected by an external diode/resistor
network.
INPUT0,1
Voltage controlled input pins with hysteresis, compatible with 3 V and 5 V CMOS
outputs. They control output switch state.
CurrentSense
Multiplexed analog sense output pin; it delivers a current proportional to the load
current.
SEn
Active high compatible with 3 V and 5 V CMOS outputs pin; it enables the
CurrentSense diagnostic pin.
SEL
Active high compatible with 3 V and 5 V CMOS outputs pin; it addresses the
CurrentSense multiplexer.
DocID027923 Rev 3
5/43
5 Page VND7140AJ12
7 V < VCC < 18 V; -40°C < Tj < 150°C
Table 9: Protections
Symbol
Parameter
Test conditions
ILIMH DC short circuit current
ILIML
TTSD
TR
TRS
Short circuit current during
thermal cycling
Shutdown temperature
Reset temperature(1)
Thermal reset of fault
diagnostic indication
VCC = 13 V
4 V < VCC < 18 V (1)
VCC = 13 V;
TR < Tj < TTSD
VSEn = 5 V
THYST
Thermal hysteresis (TTSD -
TR)(1)
ΔTJ_SD Dynamic temperature
VDEMAG
Turn-off output voltage
clamp
VON
Output voltage drop
limitation
Tj = -40 °C; VCC = 13 V
IOUT = 1 A; L = 6 mH;
Tj = -40 °C
IOUT = 1 A; L = 6 mH;
Tj = 25 °C to +150 °C
IOUT = 0.07 A
Electrical specification
Min.
8
Typ.
12
4
150
TRS + 1
175
TRS + 7
135
Max. Unit
16
16 A
200
°C
VCC - 38
7
60
K
V
VCC - 41 VCC - 46 VCC - 52
20 mV
Notes:
(1)Parameter guaranteed by design and characterization; not subject to production test.
Table 10: CurrentSense
7 V < VCC < 18 V; -40°C < Tj < 150°C
Symbol
Parameter
Test conditions
Min. Typ. Max. Unit
VSEn = 0 V; ISENSE = 1 mA -17
-12 V
VSENSE_CL CurrentSense clamp voltage
VSEn = 0 V; ISENSE = -1 mA 7 V
CurrentSense characteristics
KOL
IOUT/ISENSE
dKcal/Kcal(1)(2)
Current sense ratio drift at
calibration point
KLED
IOUT/ISENSE
dKLED/KLED(1)(2) Current sense ratio drift
K0 IOUT/ISENSE
dK0/K0(1)(2) Current sense ratio drift
K1 IOUT/ISENSE
IOUT = 0.01 A;
VSENSE = 0.5 V; VSEn = 5 V
295
IOUT = 0.01 A to 0.025 A;
Ical = 17.5 mA;
VSENSE = 0.5 V; VSEn = 5 V
-30
30 %
IOUT = 0.025 A;
VSENSE = 0.5 V; VSEn = 5 V
330
580
820
IOUT = 0.025 A;
VSENSE = 0.5 V; VSEn = 5 V
-25
25 %
IOUT = 0.07 A;
VSENSE = 0.5 V; VSEn = 5 V
375
550
720
IOUT = 0.07 A;
VSENSE = 0.5 V; VSEn = 5 V
-20
20 %
IOUT = 0.15 A;
VSENSE = 4 V; VSEn = 5 V
360 500 670
DocID027923 Rev 3
11/43
11 Page |
Páginas | Total 30 Páginas | |
PDF Descargar | [ Datasheet VND7140AJ12.PDF ] |
Número de pieza | Descripción | Fabricantes |
VND7140AJ12 | Double channel high-side driver | STMicroelectronics |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |