|
|
PDF FS-N10 Data sheet ( Hoja de datos )
| Número de pieza | FS-N10 | |
| Descripción | Digital Fiber Sensor Instruction Manual | |
| Fabricantes | Keyence | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de FS-N10 (archivo pdf) en la parte inferior de esta página. Total 6 Páginas | ||
|
No Preview Available !
Digital Fiber Sensor
FS-N10 Series
Instruction Manual
96M00603
Danger
Failure to follow these instructions may lead to death or seri-
ous injury.
Warning
Caution
Failure to follow these instructions may lead to injury.
Failure to follow these instructions may lead to product dam-
age (product malfunction, etc.)
Note Provides additional information on proper operations that can be easily mistaken.
Note
This provides tips about situations in which the feature being described is useful.
Tip
See "FS-N10 Series User's Manual" for details on the features of the FS-N10 series and
detailed instructions for configuration.
Hints on Correct Use
Warning
• This product is used to detect targets. Do not apply the
product to safety circuits for human protection.
• This product is not of explosion-proof construction. Do not
use the products in places with flammable gas, liquid, or
dust.
• This product is a sensor of DC power supply type. Do not
apply AC power. The product may explode or burn if an AC
voltage is applied.
• Do not wire the amplifier line along with power lines or high-tension lines, otherwise the sen-
sor may malfunction or receive damage due to noise.
• When using a commercially available switching regulator, ground the frame ground terminal
and ground terminal.
• Do not use the FS series outdoors, or in a place where extraneous light can enter the light-
receiving surface directly.
• Due to the individual dispersion of characteristics and the difference in fiber unit model, the
maximum sensing distance or displayed value of all the units are not the same.
• If the sensor is used in S-APC mode for a long time, the LED indicators will be imposed with
a heavy load. In that case, the sensor will be automatically set to ACC mode where the cur-
rent consumption of the sensor for light emission will be constant, and “END APC” will be
displayed. The sensor can be continuously used in this case. Replace the sensor, however, if
highly precise detection is required.
About UL Certification
The FS-N series is UL and C-UL certified, and is compliant with the UL and CSA standards.
• Applicable standards UL508 Industrial Control Equipment
CAN/CSA C22.2 No.14-M05 Industrial Control Equipment
• UL File No. E301717
• UL categories: NRKH, NRKH7
• Enclosure Type 1 (based on UL50 standard)
Notes on UL Certification
• The power source used with the FS-N series must be UL Listing certified for Class 2 output
as stipulated by US National Electric Code (NEC) NFPA70.
• Connect the FS-N12 and N14 to the FS-N11 and N13 main units for use.
Included accessories
• Instruction Manual 1pc.
• Fiber cutter
1pc.
FS-N10 Series Quick Start and Cabling
Quick Start
Fine sensitivity adjustment
Up Down
Output switch
Press the [MODE] button once, then
use to select L-on or D-on
Setting value Light intensity
Sensitivity setting
Preset function
Configure easily
with a single press
when receiving light
Power select switch *1
Press once each for workpiece/no workpiece
Standard MEGA (fixed)
*1 This is a channel switch on 2-output types.
*2 Press and hold the [MODE] button to make advanced settings.
Cabling
Note See page 4 for information about connecting to external devices other than the FS-
N11N.
Mounting Unit
Brown
DC12-24V
Black
Load
Blue
0V
Mounting on a DIN Rail
1 Align the claw at the bottom of the main body with
the DIN rail, as shown in figure1.
While pushing the main body in the direction of
the arrow 1, slant it in the direction of the arrow 2.
2 To dismount the sensor, raise the main body in
the direction of the arrow 3 while pushing the
main body in the direction of the arrow 1.
3
2
Installation on a Wall (Main Unit Only)
1 Attach the unit to the optional mounting bracket (OP-
73880), mount them together, and secure them with
two M3 screws as shown in figure2.
1
figure1
Connecting Fiber Unit
OP-73880
figure2
1 Open the dust cover in the direction shown by
arrow 1.
2 Move down the fiber lock lever in the direction
shown by arrow 2.
3 Insert a fiber unit into the fiber insertion holes
to a length of the fiber insertion sign (i.e.,
approximately 14 mm).
4 Move down the fiber lock lever in the direction
shown by arrow 4.
4
2
3
1
Fiber insertion sign
Note
• If a thin fiber unit is used, an adapter provided with the thin fiber unit will be
required.
Unless the correct adapter is connected, the thin fiber unit will not detect
targets correctly (the adapter is supplied with the fiber unit).
Cable outer dia
1.3
Adapter
Adapter A
(OP-26500)
Appearance
Adapter B
1.0 (OP-26501)
• To connect the coaxial reflective type fiber unit to the amplifier, connect the
single-core fiber to the transmitter side, and connect the multiple-core fiber
to the receiver side.
Single-core fiber
Multi-core fiber
Transmitter
Receiver
1
1 page  
Detection Settings
5V) (W0E
MODE
6Q((
Q((&MODE
Q0&
5JQ6
&'VE 5VF
MODE &'VE &V/
&'VE &V/
&'VE #4'#
&'VE
&'VE
Timer OFF
Off-delay timer *1
On-delay timer *1
One-shot timer *1
Normal (light intensity)
detection mode
DATUM1 mode *2
DATUM2 mode *2
Area detection mode
Rising Edge Detection Mode
Falling Edge Detection Mode
*6 KP Q((
MODE KP 5'V
KP 245V
KP 5J(V
KP 45V
KP .Q((
KP 2#75
KP 5.'2
Do not use external input
External calibration input
Preset input
Zero shift input
Reset input
Transmission OFF input
Pause mode transition input *3
Sleep mode transition input
#66
MODE
Light emission power selection *4
*7 #P.)
MODE
Analog scaling *5
'0&
MODE Settings complete
5V) &K52 Go to display setup mode
5V) 5;5 Go to system setup mode
5V) (W0E
Return to original
detection setup mode
Return to normal display
*1 Press the MODE button to set between the range of and (ms).
*2 Press the MODE button to set the retouch sensitivity to a range of between .'W and .'W
and set the warning output level to a range of between 12 and 2.
*3 Press the MODE button to toggle between Q((/Q0/-''2.
*4 Can be set between the range of and .
*5 Can be set between the range of and .
*6 Only external input types (FS-N11CN/N11CP/N11EN/N12EN/N13N/N13P/N14N/N14P).
*7 Only monitor output types (FS-N11MN).
Display Settings
5V) &K52
MODE
4'W Q((
Normal display method
4'W QPMODE
Reverse display
5W$ Q((
MODE 5W$ 56&'
5W$ $#4
5W$ 2'4
5W$ *.&
5W$ *.&2
5W$ .FQP
24* QP
MODE 24* Q((
'0&
MODE 5V) 5;5
5V) (W0E
5V) &K52
Do not set up sub-display
Extension display
Bar display
Excess gain display
Light intensity hold display *1
Excess gain hold display *1
L-on / D-on display
Enable the saturation of the
Preset function *2
Disable the saturation of the
Preset function
Settings complete
Go to system setup mode
Go to detection setup mode
Return to original display setup mode
Return to normal display
*1 Press the MODE button to toggle between 5VF/2`2A/D`DA/2AD`/2`DA
*2 Press the MODE button to set between the range of 2 and 2.
System Settings
5V) 5;5
MODE
#2% Q((
Disable APC
#2% QPMODE
Enable APC
'EQ Q((
MODE 'EQ QP
'EQ (W..
Do not use eco feature
Enable eco feature
Reduce power consumption
(response time 4 times slower)
)#KP 5VF
MODE )CKP (W..
KPV( 56&
MODE KPV( &Q$.
*1 .KP- Q((
MODE .KP- QP
Standard current value display
Maximum current value display
(4 times hysteresis)
Normal operation
Twice number of
interference-prevention units as 56&
(response time 2 times slower)
Disable common key operations
Enable common key operations
'0&
Settings complete
5V) (W0EMODE
Go to detection setup mode
5V) &KU2 Go to original display setup mode
5V) 5;5 Return to system setup mode
Return to normal display
*1 Main unit only.
Two Output *2
EJ 5VF
MODE EJ .K/V
MODE
Light intensity detection mode
Limit setting output mode
T5V 75'4
T5V #WVQ
EJ #.TV
6Q((
Q((&MODE
Q0&
5JQ6
User reset
Auto reset
Warning output mode
Timer OFF
Off-delay timer *1
On-delay timer *1
One-shot timer *1
'0&
MODE
Settings complete
Return to normal display
*1
Press
MODE
the
button
to set
between
the
range
of
and
(ms).
*2 Only 2 output types (FS-N13N/N13P/N14N/N14P/N13CP/N14CP).
5
5 Page | ||
| Páginas | Total 6 Páginas | |
| PDF Descargar | [ Datasheet FS-N10.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| FS-N10 | Digital Fiber Sensor Instruction Manual | Keyence |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |