|
|
PDF MT79338 Data sheet ( Hoja de datos )
| Número de pieza | MT79338 | |
| Descripción | AC-DC LED Driver | |
| Fabricantes | Maxic Technology | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de MT79338 (archivo pdf) en la parte inferior de esta página. Total 7 Páginas | ||
|
No Preview Available !
Maximizing IC Performance
MT79338
Single Stage, High PFC, AC-DC LED Driver
DESCRIPTION
MT79338 is a single-stage，primary side control
AC-DC LED driver with active power factor
correction. MT79338 integrates on-chip PFC
circuit operates in critical conduction mode (CRM)
to achieve high power factor and reduce the
power MOSFET switching loss. With MAXIC
Proprietary control technique, precision LED
current is achieved without secondary side
sense and feedback circuit including
opto-coupler.
Embedded with 600V power MOSFET, the
peripheral circuit is simplified.
MT79338 provides various protections, such as
over current protection (OCP), over voltage
protection (OVP), short circuit protection (SCP)
and over temperature protection (OTP), etc, to
improve system reliability.
FEATURES
Single-stage Active PFC for high power
factor and low THD
Primary side control eliminates opto-coupler
High precision LED current (+/-3%)
Critical Conduction Mode operation
Cycle-by-cycle current limiting
Under-voltage lockout (UVLO) protection
VDD and output over voltage protection
Adjustable constant current and output
power setting
Power on soft-start
Embedded with 600V power MOSFET
DIP8 package
APPLICATIONS
AC/DC LED driver applications
Signal and decorative LED lighting
E27/PAR30/PAR38/GU10 etc.LED lamp
T8/T10 LED String
Typical Application Circuit
Vin_ac
R5
C1
C2
R2 D2
R6
D1 Lp
C3 La
R3
C4
MT79338
4
COMP
GND 3
5 DSEN
CS 2
6 VDD
DRAIN 7
1 SMOUTR7C99E0 DRAIN 8
R4
Rs
D3
Ls R10
VLED+
C5
VLED-
MT79338 Rev. 1.05
www.maxictech.com
Copyright © 2014 Maxic Technology Corporation
Page 1
1 page  
Maximizing IC Performance
MT79338
Single Stage, High PFC, AC-DC LED Driver
Auxiliary Sensing
The turning-on of power MOSFET is controlled
by sensing DSEN’s waveform, which is sampled
from Auxiliary windings by the resistor-divider. As
DSEN’s waveform goes below 0V at OFF time,
which indicates the drain of power MOSFET
damps to its valley or nearby, MT79338 turns on
the power MOSFET. Besides, minimum OFF
time control provide noise immunity.
Furthermore, MT79338 features over-voltage
protection (OVP), short-circuit protection (SCP),
and over-current protection (OCP) functions.
Those protections are triggered by sensing the
auxiliary winding waveform information, as the
auxiliary winding voltage is proportional to the
output voltage (secondary winding voltage)
during the OFF time period. The auxiliary
winding voltage is sampled by DSEN pin, one
LEB (Leading Edge Blanking) time right after
DRV signal is turned off.
Auxiliary sensing function is shown in Fig.3.
DRV
DSEN
Sampling Point
LEB=2uS
(typ)
Fig.3 Auxiliary Signal Sensing
Over-voltage Protection
MT79338 is implemented with two over-voltage
protection schemes: (1) If DSEN pin’s voltage is
detected above 3.2V for three times, (refer to
Auxiliary Sensing section), MT79338 turns off
the PWM switching signal, and VDD voltage
gradually drops to UVLO threshold, and the
system will be re-started. The threshold voltage
of over-voltage protection VOUT_OV, can be easily
defined as (refer to the application circuit in page
1):
VOUT _OV
3.2 (1
R3)
R4
Ns
Na
VD3
Where Ns is the secondary winding, Na is
auxiliary winding, VD3 is the forward bias of the
secondary side rectifier diode.
(2) If VDD pin’s voltage exceeds 24V three times,
MT79338 turns off the PWM switching signal,
and VDD gradually drops to UVLO threshold,
and then the system will be re-started. It is highly
recommended to set up the VDD voltage
between 12V and 22V by designed a proper Na
to Ns ratio of the transformer.
Short-circuit Protection
The short-circuit protection is triggered if the
DSEN pin voltage is detected below 400mV at
OFF period for a continuous time of 5 to 10ms.
The gate drive switching will be turned off, and a
restart process will be kicked off when the VDD
voltage drops below the UVLO threshold.
This re-start process will repeat if the short-circuit
condition continues to exist.
Over-current Protection
MT79338 immediately turns off the power
MOSFET once the voltage at CS pin exceeds
1.8V. This cycle by cycle current limitation
scheme prevents the relevant components, such
as power MOSFET, transformer, etc. from
damage.
MT79338 Rev. 1.05
www.maxictech.com
Copyright © 2014 Maxic Technology Corporation
Page 5
5 Page | ||
| Páginas | Total 7 Páginas | |
| PDF Descargar | [ Datasheet MT79338.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| MT7933 | AC-DC LED Driver | Maxic Technology |
| MT79332 | AC-DC LED Driver | Maxic Technology |
| MT79338 | AC-DC LED Driver | Maxic Technology |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |