DataSheet39.com

What is AX1011?

This electronic component, produced by the manufacturer "Nedap", performs the same function as "RS422-module".


AX1011 Datasheet PDF - Nedap

Part Number AX1011
Description RS422-module
Manufacturers Nedap 
Logo Nedap Logo 


There is a preview and AX1011 download ( pdf file ) link at the bottom of this page.





Total 3 Pages



Preview 1 page

No Preview Available ! AX1011 datasheet, circuit

®
AX1011
AX1011
RS422-module for AP1003
Installation sheet
GENERAL
The AX1011 is intended to connect certain XS-controllers (MD300 loop) to AEOS (AP1003). The
XS controllers are changed in such a way that their Inputs/Outputs behave exactly like AEpack
In/Outputs. This means that a full functional AEOS system can be built utilizing existing XS
hardware.
The AX1001 is connected to the AP1003 (only suitable for the upper connector). The RS232 signal of
the AP1003 is converted to an isolated RS422 signal, which is used to connect an MD300 loop of XS
controllers.
To connect the XS Controller loop to AEOS using the AX1011 special firmware is required at the
AP1003 and the connected XS-controllers in the MD300 loop.
CONNECTIONS
Place the AX1011 at the upper connector of the AP1003. The original signals of the AP1003 (except
for Tx1,GND and Rx1) are lead to the screw connector of the AX1011.
Attention: Signals of pin 8 and higher are at the AX1011 located at another pin than the original
AP1003 (see figure below).
AP1003 connectors
Vlock
NC
RY1
*
CROYM1 *
NO
RY1
*
IN1
GND
IN3
Tx1 GND Rx1
+5V
out
+12V
out
1 2 3 4 5 6 7 8 9 10 11 12
GND
NC
RY2
COM
RY2
NO
RY2
IN2 GND IN4
Tx2 GND Rx2
RDP RCP
UL* NA*
13 14 15
UL GND NA
16
CLS
AX1011
Rx Tx
Pow
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Vlock
NC
RY1
COM
RY1
NO
RY1
IN1 GND IN3
Tx+
Tx-
Rx+
Rx-
+5V +12V
out out
UL* NA*
AX1011 connector
MD300 board at XS-controller
Cable shield to GND
and metal case
To next controllers
(max 8)
AX1011
Tx+
Tx-
Rx+
Rx-
Cable shield: case
XS-controller
MD 300 ‘Previous’
R+
R-
T+
T-
Cable shield: case
Cable shield: Cable shield must always be connected to metal case on both sides (AEpack and
XS-controller).
Date : 2 December 2004
Version: 1
Part.no.: 5257980
This information is furnished for guidance, and with no guarantee as to its accuracy or completeness; its publication conveys no licence under any patent or
other right, nor does the publisher assume liability for any consequence of its use; specifications and availability of goods mentioned in it are subject to change
without notice; it is not to be reproduced in any way, in whole or in part, without the written consent of the publisher.
© Nedap N.V., IDEAS P.O. Box 103 NL-7140 AC GROENLO The Netherlands
Page 1 of 3


Part Details

On this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for AX1011 electronic component.


Information Total 3 Pages
Link URL [ Copy URL to Clipboard ]
Download [ AX1011.PDF Datasheet ]

Share Link :

Electronic Components Distributor


An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists.


SparkFun Electronics Allied Electronics DigiKey Electronics Arrow Electronics
Mouser Electronics Adafruit Newark Chip One Stop


Featured Datasheets

Part NumberDescriptionMFRS
AX1011The function is RS422-module. NedapNedap
AX1012The function is RS232 to RS422/485 converter. NedapNedap

Semiconductors commonly used in industry:

1N4148   |   BAW56   |   1N5400   |   NE555   |  

LM324   |   BC327   |   IRF840  |   2N3904   |  



Quick jump to:

AX10     1N4     2N2     2SA     2SC     74H     BC     HCF     IRF     KA    

LA     LM     MC     NE     ST     STK     TDA     TL     UA    



Privacy Policy   |    Contact Us     |    New    |    Search