DataSheet39.com

What is UMFT230XA?

This electronic component, produced by the manufacturer "FTDI", performs the same function as "USB to Basic UART Development Module".


UMFT230XA Datasheet PDF - FTDI

Part Number UMFT230XA
Description USB to Basic UART Development Module
Manufacturers FTDI 
Logo FTDI Logo 


There is a preview and UMFT230XA download ( pdf file ) link at the bottom of this page.





Total 18 Pages



Preview 1 page

No Preview Available ! UMFT230XA datasheet, circuit

Future Technology
Devices International
Datasheet
UMFT230XA USB to Basic
UART Development Module
UMFT230XA Datasheet
Version 1.3
Document Reference No.: FT_000519 Clearance No.: FTDI# 269
UMFT230XA is a USB to Basic UART DIP module with a 0.3” row pitch.
1 Introduction
1.1 Features
The UMFT230XA is a development module
for FTDI’s FT230XQ, one of the devices
from FTDI’s range of USB interface bridging
integrated circuit devices. FT230X is a USB
to UART interface with a battery charger
detection feature, which can allow batteries
to be charged with a higher current from a
dedicated charger port (without the
FT230X being enumerated). In addition,
asynchronous and synchronous bit bang
interface modes are available. The
internally generated clock (6MHz, 12MHz
and 24MHz) can be brought out of the on
one of the CBUS pin to be used to drive a
microprocessor or external logic.
The UMFT230XA is a module which is
designed to plug into a standard 0.3” wide
16 pin DIP socket. All components used,
including the FT230XQ are Pb-free (RoHS
compliant).
The UMFT230XA is fitted with a FT230XQ; all
the features of the FT230X can be utilized with
the UMFT230XA. For a full list of the FT230X’s
features please see the FT230X datasheet which
can be found by clicking here.
In addition to the features listed in the FT230X
datasheet, the UMFT230XA has the following
features:
Small PCB assembly module designed to fit
a standard 7.62mm (0.3”) wide 16 pin DIP
socket. Pins are on a 2.54mm (0.1”) pitch.
On board USB ‘mini-B’ socket allows module
to be connected to a PC via a standard A to
mini-B USB cable.
Functionally configurable using solder links.
The default solder links setup enables the
module to function without peripheral wires
or application board. Other configurations
enable external power supply options and
variation of logic reference levels.
Use of FTDI devices in life support and/or safety applications is entirely at the user’s risk, and the user agrees
to defend, indemnify and hold harmless FTDI from any and all damages, claims, suits or expense resulting
from such use.

line_dark_gray
UMFT230XA equivalent
UMFT230XA Datasheet
Version 1.3
Document Reference No.: FT_000519 Clearance No.: FTDI# 269
4.2 Signal Descriptions
Pin No. Name
Type
Description
J1-1,
J2-8
GND
PWR
Module Ground Supply Pins
J1-2
3V3OUT
Power
Input/
Output
3.3V output from integrated LDO regulator. This pin is decoupled with a 100nF
capacitor to ground on the PCB module. The prime purpose of this pin is to provide
the 3.3V supply that can be used internally. For power supply configuration details
see section 5.
J1-3
VCCIO
Power
Input
+1.8V to +3.3V supply to the UART Interface and CBUS I/O pins. For power supply
configuration details see section 5.
J1-4
RESET# Input
FT230X active low reset line. Configured with an on board pull-up and recommended
filter capacitor.
J1-5
CTS#
Input Clear To Send Control Input / Handshake Signal.
J1-6
RTS#
Output Request to Send Control Output / Handshake Signal.
J1-7
RXD
Input Receiving Asynchronous Data Input.
J1-8
TXD
Output Transmit Asynchronous Data Output.
J2-1
SLD
GND
USB Cable Shield. Connected to GND via a 0ohm resistor.
J2-2
VBUS
Power
Output
5V Power output from the USB bus. For a low power USB bus powered design, up to
100mA can be sourced from the 5V supply and applied to the USB bus. A maximum
of 500mA can be sourced from the USB bus in a high power USB bus powered design.
Currents up to 1A can be sourced from a dedicated charger and applied to the USB
bus.
J2-3
VCC
Power
Input
5V power input for FT230X. For power supply configuration details see section 5.
J2-4
CBUS3
I/O
Configurable CBUS I/O Pin. Function of this pin is configured in the device internal
MTP ROM. . See CBUS Signal Options, Table 4.2.
J2-5
CBUS2
I/O
Configurable CBUS I/O Pin. Function of this pin is configured in the device internal
MTP ROM.. See CBUS Signal Options, Table 4.2.
J2-6
CBUS1
I/O
Configurable CBUS I/O Pin. Function of this pin is configured in the device internal
MTP ROM.. See CBUS Signal Options, Table 4.2.
J2-7
CBUS0
I/O
Configurable CBUS I/O Pin. Function of this pin is configured in the device internal
MTP ROM. See CBUS Signal Options, Table 4.2.
Table 4.1 Module Pin Out Description
5
Copyright © 2013 Future Technology Devices International Limited


line_dark_gray

Preview 5 Page


Part Details

On this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for UMFT230XA electronic component.


Information Total 18 Pages
Link URL [ Copy URL to Clipboard ]
Download [ UMFT230XA.PDF Datasheet ]

Share Link :

Electronic Components Distributor


An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists.


SparkFun Electronics Allied Electronics DigiKey Electronics Arrow Electronics
Mouser Electronics Adafruit Newark Chip One Stop


Featured Datasheets

Part NumberDescriptionMFRS
UMFT230XAThe function is USB to Basic UART Development Module. FTDIFTDI

Semiconductors commonly used in industry:

1N4148   |   BAW56   |   1N5400   |   NE555   |  

LM324   |   BC327   |   IRF840  |   2N3904   |  



Quick jump to:

UMFT     1N4     2N2     2SA     2SC     74H     BC     HCF     IRF     KA    

LA     LM     MC     NE     ST     STK     TDA     TL     UA    



Privacy Policy   |    Contact Us     |    New    |    Search