KIA6281H Datasheet PDF - KEC
| Part Number | KIA6281H | |
| Description | 5.8W DUAL AUDIO POWER AMPLIFIER | |
| Manufacturers | KEC | |
| Logo |  |
|
|
There is a preview and KIA6281H download ( pdf file ) link at the bottom of this page. Total 11 Pages | ||
Preview 1 page No Preview Available !
KEC
"
SEMICONDUCTOR
TECHNICAL DATA
KIA6281H
BIPOLAR LINEAR INTEGRATED CIRCUIT
5.8W DUAL AUDIO POWER AMPLIFIER.
22W BTL AUDIO POWER AMPLIFIER.
The KIA6281H is dual audio power amplifier
for consumer application.
It is designed for high power, low distortion and
low noise.
It also contains various kind of protectors.
It is suitable for car-audio power amplifier with
high performance.
FEATURES
* High Power
PouTd)=22W(Typ.)
(Vcc=14.4V, f=lkHz, THD=10%, RL=4&, BTL)
PouT(2)=19W(Typ.)
(Vcc=13.2V, f=lkHz, THD=10%, RL=4&, BTL)
PouT(3)=15W(Typ.)
(Vcc=13.2V, f=lkHz, THD=1%, RL=4&, BTL)
PouT(4)=5.8W(Typ.)/ch
(VCc=13.2V, f=lkHz, THD=10%, RL=4&, DUAL).
* Low Distortion
THD(l)=0.03% (Typ.)
(Vcc=13.2V, f=lkHz, POUT=4W, Gv=40dB, RL=4&, BTL)
THD(2)=0.06% (Typ.)
(Vcc=13.2V, f=lkHz, POUT=1W, Gv=52dB, RL=4&, DUAL).
* Low Noise
VNo(i)=0.14mVrms (Typ.)
(Vcc=13.2V, RL=4^, Gv=40dB, Rg=0, DIN Noise : DIN45405)
VNo(2)=0.7mVrms (Typ.)
(Vcc=13.2V, RL=4&, Gv=52dB, Rg=10k&, BW=20Hz~ 20kHz, DUAL).
* Protector Circuit
Thermal shut down, over voltage protection
Out-Vcc short, OUT-GND short and Out-Out short protection.
* Operating supply voltage range
Vcc=9~18V.
CPP-12
DIM
A
B
D
d
G
HI
H2
LI
L2
M
N
PI
P2
Q
Rl
R2
S
T
MILLIMETERS
22.6± 0.2
4.0± 0.2
1.1±0.1
0.55±0.1
1.55± 0.2
11.25± 0.3
14.5±0.3
6.55± 0.3
7.05± 0.3
2 . 0 7 5 TYP.
1.5 TYP.
1.778
2.0
3.7± 0.2
0.4
R1.85
15.6± 0.2
0.4+0.1/-0.05
1997. 5. 8
Revision No : 0
KEC
1/11
|
| |
 
KIA6281H
Amp. 1 is noninverting amplifier and Amp. 2 is invert one.
The output voltage is divided by resistors R3 and R4.
The divided voltage is applied to inverting input of Amp. 2.
R3 and R4 are determined in the following equation.
20 log
(dB) Gv in Dual Mode
The voltage gain in this circuit is 6dB higher than that in Dual Mode.
Gv = 201og
Rf + R1 +
Rf + R
R2
+
6(dB)
In case of Rf=0
Gv=52+6=58(dB)
In case of Rf=430^
Gv=34+6=40(dB)
Each voltage gain can be set as shown above.
2.MUTING
Audio muting can be accomplished by connecting pin © (ripple filter) to GND as shown in Fig. 3.
Then, the bias circuits are cut off.
However, caution must be exercised to the following items.
(1) The recovery time from the muting operation is determined by the capacities
of the ripple filter capacitor between © pin and GND, and of the capacitor for NF.
(2) As this muting system is operated by the short-circuit of ripple filter : C5, the
ripple rejection ratio becomes worse in the muting condition.
At mute ON, some pop noises of breaking the bias are produced.
Fig. 3
1997. 5. 8
Revision No : 0
KEC
5/11
Preview 5 Page |
Part DetailsOn this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for KIA6281H electronic component. |
| Information | Total 11 Pages | |
| Link URL | [ Copy URL to Clipboard ] | |
| Download | [ KIA6281H.PDF Datasheet ] | |
Share Link :
Electronic Components Distributor
|
An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists. |
| SparkFun Electronics | Allied Electronics | DigiKey Electronics | Arrow Electronics |
| Mouser Electronics | Adafruit | Newark | Chip One Stop |
Featured Datasheets
| Part Number | Description | MFRS |
| KIA6281H | The function is 5.8W DUAL AUDIO POWER AMPLIFIER. KEC | |
Semiconductors commonly used in industry:
1N4148 |
BAW56 |
1N5400 |
NE555 | | ||
Quick jump to:
KIA6
1N4
2N2
2SA
2SC
74H
BC
HCF
IRF
KA | ||