DataSheet39.com

What is UT0324-41?

This electronic component, produced by the manufacturer "Ledtech", performs the same function as "3.0mm ROUND LED LAMP".


UT0324-41 Datasheet PDF - Ledtech

Part Number UT0324-41
Description 3.0mm ROUND LED LAMP
Manufacturers Ledtech 
Logo Ledtech Logo 


There is a preview and UT0324-41 download ( pdf file ) link at the bottom of this page.





Total 6 Pages



Preview 1 page

No Preview Available ! UT0324-41 datasheet, circuit

LEDTECH ELECTRONICS CORP.
USA Sales Office
19209 Parthenia Street - Suite D
Northridge, CA 91324
Phone: (818) 701-7240
Fax: (818) 701-7217
SPECIFICATION
PART NO. : UT0324-41
3.0mm ROUND LED LAMP
Approved by
Tung
Checked by
Yang
Prepared by
Qing

line_dark_gray
UT0324-41 equivalent
UT0324-41
3.0mm ROUND
LED LAMP
Precautions:
TAKE NOTE OF THE FOLLOWING IN USE OF LED
1. Temperature in use
Since the light generated inside the LED needs to be emitted to outside efficiently, a resin with
high light transparency is used; therefore, additives to improve the heat resistance or moisture
resistance (silica gel , etc) which are used for semiconductor products such as transistors
cannot be added to the resin.
Consequently, the heat resistant ability of the resin used for LED is usually low; therefore,
please be careful on the following during use.
Avoid applying external force, stress, and excessive vibration to the resins and terminals at
high temperature. The glass transition temperature of epoxy resin used for the LED is
approximately 120-130 .
At a temperature exceeding this limit, the coefficient of liner expansion of the resin doubles or
more compared to that at normal temperature and the resin is softened.
If external force or stress is applied at that time, it may cause a wire rupture.
2. Soldering
Please be careful on the following at soldering.
After soldering, avoided applying external force, stress, and excessive vibration until the
products go to cooling process (normal temperature), <Same for products with terminal leads>
(1) Soldering measurements:
Distance between melted solder side to bottom of resin shall be 1.6mm or longer.
(2) Dip soldering :
Pre-heat: 90 max. (Backside of PCB), Within 60 seconds.
Solder bath: 260 5 (Solder temperature), Within 5 seconds.
(3) Hand soldering: 350 max. (Temperature of soldering iron tip), Within 3 seconds.
3. Insertion
Pitch of the LED leads and pitch of mounting holes need to be same
4. Others
Since the heat resistant ability of the LED resin is low, SMD components are used on the same
PCB, please mount the LED after adhesive baking process for SMD components. In case
adhesive baking is done after LED lamp insertion due to a production process reason, make
sure not to apply external force, stress, and excessive vibration to the LED and follow the
conditions below.
Baking temperature: 120 max. Baking time: Within 60 seconds
If soldering is done sequentially after the adhesive baking, please perform the soldering after cooling down
the LED to normal temperature.
VER.: 01 Date: 2007/01/18 Page: 4/5


line_dark_gray

Preview 5 Page


Part Details

On this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for UT0324-41 electronic component.


Information Total 6 Pages
Link URL [ Copy URL to Clipboard ]
Download [ UT0324-41.PDF Datasheet ]

Share Link :

Electronic Components Distributor


An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists.


SparkFun Electronics Allied Electronics DigiKey Electronics Arrow Electronics
Mouser Electronics Adafruit Newark Chip One Stop


Featured Datasheets

Part NumberDescriptionMFRS
UT0324-41The function is 3.0mm ROUND LED LAMP. LedtechLedtech

Semiconductors commonly used in industry:

1N4148   |   BAW56   |   1N5400   |   NE555   |  

LM324   |   BC327   |   IRF840  |   2N3904   |  



Quick jump to:

UT03     1N4     2N2     2SA     2SC     74H     BC     HCF     IRF     KA    

LA     LM     MC     NE     ST     STK     TDA     TL     UA    



Privacy Policy   |    Contact Us     |    New    |    Search