|
|
Número de pieza | LAM170M023A | |
Descripción | Display Module | |
Fabricantes | Japan Display | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de LAM170M023A (archivo pdf) en la parte inferior de esta página. Total 30 Páginas | ||
No Preview Available ! 仕様書パターン 2 CAS表紙
To : Mindray Medical International, Ltd.
August 27, 2013
TECHNICAL DATA
Product Name
LAM170M023A
(NOTES)
1. This document may, wholly or partially, be subject to change without notice.
2. All rights are reserved ; No one is permitted to reproduce, duplicate or distribute in any form,
the whole or part of this document without Japan Display's prior written consent.
3. No one is permitted to explain nor disclose the contents of this document to third parties without
Japan Display's prior written consent.
4. Japan Display will not be held responsible for any damage to the user that may result from accidents
or any other reasons during operation of the user's unit according to this document, any previous
reports or oral discussions.
5. Circuitry and other examples described herein are meant merely to indicate the characteristics and
performance of Japan Display's products.
Japan Display assumes no responsibility for any intellectual property claims or other problems that
may result from applications based on the examples described herein.
6. No license is granted by implication or otherwise under any patents or other rights of any third
party or Japan Display Inc.
7. LIFE SUPPORT APPLICATIONS : The product covered by this document is not authorized for
use in LIFE SUPPORT SYSTEMS.
1 page DESCRIPTION
This specification is applied to the following 17inch SXGA IPS-Pro-TFT module.
Note : The LED driver for back light unit is built in this module.
General Specifications
Part Name
: LAM170M023A
Effective Display Area
: H337.92 × V270.336 [mm]
Number of Pixels
: H1280 × V1024 [pixels]
Pixel Pitch
: H0.264 × V0.264 [mm]
Color Pixel Arrangement : R+G+B Vertical Stripe
Display Mode
: Transmissive Mode
Normally Black Mode
IPS-Pro
Top Polarizer Type
: Anti-glare(Hardness:2H)
Number of Colors
: 16,777,216 colors
Viewing Angle Range
: Super Wide Version
Input Signal
: 2-channel LVDS (LVDS:Low Voltage Differential Signaling)
Back Light
: Edge Light Type with White LED
External Dimensions
: (H) 368.0 × (V) 306.0 × (t) 19.9 (mm)
Weight
: 1600 g typ.
Japan Display Inc.
Date
August
27,
2013
Sh.
No.
DPBC10000517-1
Page 4-1/1
5 Page 3.2 BACK LIGHT
Item
Symbol
Min.
Typ.
Input Voltage
Input Current
ON/OFF
Control Voltage
ON
OFF
VIN
IIN
ON/OFF
10.8
—
2.5
0
12.0
1.0
3.3
—
Current
IBL
Brightness Control Voltage
VBC
IBC
PWM dimming signal
Input Voltage
PWM
High
Low
—
1.0
—
2.5
0
—
3.3
—
3.3
—
PWM Frequency
IPWM
PWMf
—
140
1.0
150
Notes
1) IIN Typ: VIN=12.0V, ON/OFF=3.3V, PWM=100%(PWMf=150Hz)
IIN Max: VIN=10.8V, ON/OFF=3.3V, PWM=100%(PWMf=150Hz)
Max.
13.2
1.44
5.0
0.5
1.0
3.6
1.0
5.0
0.9
—
160
Unit
V
A
V
V
mA
V
mA
V
V
mA
Hz
Ta=25°C
Note
—
1), 2)
B/L=ON
B/L=OFF
ON/OFF=5.0V
3),5)
VBC=3.6V
4),5),7)
6)
—
2) As this module contains current fuse(3.0A),please prepare current source that is enough for cutting current fuse
(larger than 8.0A) or set protection circuit when a trouble happens.
3) Brightness Control (Reference value)
4) Brightness Control (Reference value)
VBC (Typ.)
1.0V
Brightness
20%
PWM (Typ.) Brightness
5% 5%
1.3V
30%
10% 10%
1.5V
40%
20% 20%
1.8V
50%
30% 30%
2.0V
60%
40% 40%
2.3V
70%
50% 50%
2.5V
80%
60% 60%
2.8V
90%
70% 70%
Above 3.0V 100%
80% 80%
90% 90%
In case of using VBC for brightness control,
100%
100%
Backlight flickering may be seen due to
Display image may look unstable if the on-duty ratio
electrical noise caused by Power Supply ability. is less than 5%.
Please check it with your actual set.
VBC should be set more than 1.0V.
Display image may look unstable if VBC is
less than 1.0V.
5) These signals can’t input at the same time.(Unused pin is to be left open.)
6) PWM pin has inrush current during PWM signal is to be high, this value depends on output impedance
of external device. For example, Pulse Generator with 50ohm output impedance has 27mA
PWM input current (IPWM) of this LED driver during 50μs.
7) Resolution of PWM signal has to be 256 at a maximum.
Japan Display Inc.
Date
August
27,
2013
Sh.
No.
DPBC10000517-1
Page 7-2/2
11 Page |
Páginas | Total 30 Páginas | |
PDF Descargar | [ Datasheet LAM170M023A.PDF ] |
Número de pieza | Descripción | Fabricantes |
LAM170M023A | Display Module | Japan Display |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |