|
|
Número de pieza | V370H3-LH3 | |
Descripción | TFT LCD Module | |
Fabricantes | CHI MEI | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de V370H3-LH3 (archivo pdf) en la parte inferior de esta página. Total 30 Páginas | ||
No Preview Available ! Global LCD Panel Exchange Center
www.panelook.com
Issued Date: Jul. 29, 2009
Model No.: V370H3-LH3
Tentative
TFT LCD Tentative Specification
MODEL NO.: V370H3 – LH3
ʳ
ʳ
ʳ
Approved By
TVHD
Chao-Chun Chung
Reviewed By
QA Dept.
Hsin-nan Chen
Product Development Div.
WT Lin
LCD TV Marketing and Product Management Div.
Prepared By
Josh Chi
Chloe Chen
1
The information described in this technical specification is tentative and it is possible to be changed without prior notice.
Please contact CMO ’s representative while your product design is based on this specification.
Version 1.1
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
1 page Global LCD Panel Exchange Center
www.panelook.com
Issued Date: Jul. 29, 2009
Model No.: V370H3-LH3
Tentative
2. ABSOLUTE MAXIMUM RATINGS
2.1 ABSOLUTE RATINGS OF ENVIRONMENT
Item
Storage Temperature
Operating Ambient Temperature
Shock (Non-Operating)
Vibration (Non-Operating)
Symbol
TST
TOP
SNOP
VNOP
Value
Min. Max.
-20 +60
0 +50
- 50
- 1.0
Note (1) Temperature and relative humidity range is shown in the figure below.
Unit Note
ºC (1)
ºC (1), (2)
G (3), (5)
G (4), (5)
(a) 90 %RH Max. (Ta Љ 40 ºC).
(b) Wet-bulb temperature should be 39 ºC Max. (Ta > 40 ºC).
(c) No condensation.
Note (2) The maximum operating temperature is based on the test condition that the surface temperature of
display area is less than or equal to 65 ºC with LCD module alone in a temperature controlled chamber.
Thermal management should be considered in final product design to prevent the surface temperature of
display area from being over 65 ºC. The range of operating temperature may degrade in case of improper
thermal management in final product design.
Note (3) 11 ms, half sine wave, 1 time for ± X, ± Y, ± Z.
Note (4) 10 ~ 200 Hz, 10 min, 1 time each X, Y, Z.
Note (5) At testing Vibration and Shock, the fixture in holding the module has to be hard and rigid enough
so that the module would not be twisted or bent by the fixture.
Relative Humidity (%RH)
100
90
80
60
Operating Range
40
20
10 Storage Range
-40 -20
0 20 40
Temperature (ºC)
60 80
5
The information described in this technical specification is tentative and it is possible to be changed without prior notice.
Please contact CMO ’s representative while your product design is based on this specification.
Version 1.1
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
5 Page Global LCD Panel Exchange Center
www.panelook.com
Issued Date: Jul. 29, 2009
Model No.: V370H3-LH3
Tentative
3.2.3 INVERTER INTERTFACE CHARACTERISTICS
Parameter
Symbol
Test
Condition
Value
Min. Typ. Max.
Unit
Note
On/Off Control Voltage ON
OFF
VBLON
Ё
Ё
2.0 Ё 5.0 V
0 Ё 0.8 V
Internal PWM Control MAX
Voltage
MIN
VIPWM
Ё 3.15 3.3 3.45 V Maximum duty ratio
Ё 0 Ё V Minimum duty ratio
External PWM Control
Voltage
HI
LO
VEPW M
Ё
2.0 Ё 5.0 V Duty on
0 Ё 0.8 V Duty off
Status Signal
HI
LO
Status
Ё
3.0 3.3 3.6
0 Ё 0.8
V Normal
V Abnormal
VBL Rising Time
VBL Falling Time
Tr1
Tf1
Ё
Ё
30
30
Ё
Ё
Ё
Ё
ms
ms 10%-90%VBL
Control Signal Rising Time
Tr Ё Ё Ё 100 ms
Control Signal Falling Time
PWM Signal Rising Time
PWM Signal Falling Time
Input impedance
PWM Delay Time
BLON Delay Time
BLON Off Time
Tf
TPW MR
TPW MF
RIN
TPW M
Ton
Ton1
Toff
Ё
Ё
Ё
Ё
Ё
Ё
Ё
Ё
Ё Ё 100 ms
Ё Ё 50 us
Ё Ё 50 us
1 Ё Ё M˖
100 Ё ms
300 Ё Ё ms
300 Ё Ё ms
300 Ё Ё ms
Note (1) The Dimming signal should be valid before backlight turns on by BLON signal. It is inhibited to
change the internal/external PWM signal during backlight turn on period.
Note (2) The power sequence and control signal timing are shown in the following figure. For a certain
reason, the inverter has a possibility to be damaged with wrong power sequence and control
signal timing.
Note (3) While system is turned ON or OFF, the power sequences must follow as below descriptions:
ψ ψTurn ON sequence: VBL Ш PWM signal Ш BLON
Turn OFF sequence: BLOFF PWM signal VBL
11
The information described in this technical specification is tentative and it is possible to be changed without prior notice.
Please contact CMO ’s representative while your product design is based on this specification.
Version 1.1
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
11 Page |
Páginas | Total 30 Páginas | |
PDF Descargar | [ Datasheet V370H3-LH3.PDF ] |
Número de pieza | Descripción | Fabricantes |
V370H3-LH1 | LCD Module | CMI MEI |
V370H3-LH3 | TFT LCD Module | CHI MEI |
V370H3-LH4 | TFT LCD Module | CHI MEI |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |