DataSheet39.com

What is PLG0E392MDO1?

This electronic component, produced by the manufacturer "Nichicon", performs the same function as "CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS".


PLG0E392MDO1 Datasheet PDF - Nichicon

Part Number PLG0E392MDO1
Description CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
Manufacturers Nichicon 
Logo Nichicon Logo 


There is a preview and PLG0E392MDO1 download ( pdf file ) link at the bottom of this page.





Total 2 Pages



Preview 1 page

No Preview Available ! PLG0E392MDO1 datasheet, circuit

CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
LG Radial Lead Type, Higher Capacitance
series
Higher Capacitance, Low ESR, High ripple current.
Load life of 2000 hours at 105°C.
Radial lead type :
Lead free flow soldering condition correspondence
Compliant to the RoHS directive (2002/95/EC).
LG
Higher
Capacitance
Specifications
LF
Item
Performance Characteristics
Category Temperature Range 55 to +105°C
Rated Voltage Range
2.5 to 16V
Rated Capacitance Range 330 to 3900µF
Capacitance Tolerance
± 20% at 120Hz, 20°C
Tangent of loss angle (tan δ) Less than or equal to the specified value at 120Hz, 20°C
ESR ( 1)
Less than or equal to the specified value at 100kHz, 20°C
Leakage Current ( 2) Less than or equal to the specified value. After 2 minutes' application of rated voltage at 20°C
Temperature Characteristics
(Max.Impedance Ratio)
Z+105°C / Z+20°C 1.25
Z55°C / Z+20°C 1.25
(100kHz)
Endurance
The specifications listed at right shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 2000 hours at 105°C.
Capacitance change
tan δ
ESR ( 1)
Leakage current ( 2)
Within ± 20% of the initial capacitance value ( 3)
150% or less than the initial specified value
150% or less than the initial specified value
Less than or equal to the initial specified value
Damp Heat
(Steady State)
The specifications listed at right shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 1000 hours at 60°C, 90% RH.
Capacitance change
tan δ
ESR ( 1)
Leakage current ( 2)
Within ± 20% of the initial capacitance value ( 3)
150% or less than the initial specified value
150% or less than the initial specified value
Less than or equal to the initial specified value
Resistance to
Soldering Heat
After soldering the capacitor under the soldering conditions prescribed
here as preheat at 150 to 200°C for 60 to 180 seconds and peak
temperature at 265°C for 10 seconds or less, the capacitor shall meet
the specifications listed at right, provided that its temperature profile is
measured at both of terminal ends facing the soldering side.
Capacitance change
tan δ
ESR ( 1)
Leakage current ( 2)
Within ± 10% of the initial capacitance value ( 3)
130% or less than the initial specified value
130% or less than the initial specified value
Less than or equal to the initial specified value
Marking
Navy blue print on the case top
1 ESR should be measured at both of the terminal ends closest to the capacitor body.
2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120
minutes at 105°C.
3 Initial value : The value before test of examination of resistance to soldering.
Dimensions
Capacitance
Resin coated Case
Voltage(g:4V)
Silvered lead Wire
Series
Lot. No.
L+0.5MAX.
φd
15MIN
4MIN
(mm)
Size φ8 × 9L φ8 × 12L φ10 × 13L
φD 8.0
8.0 10.0
L 8.5 11.5 12.5
P 3.5 3.5 5.0
φd 0.6 0.6 0.6
Voltage
V
Code
2.5
e
Please refer to page 20 about the end seal configulation.
4
g
6.3 10
jA
16
C
Type numbering system (Example : 4V 1200µF)
1 2 3 4 5 6 7 8 9 10 11 12
P LG 0G 1 2 2 MCO 1
Size code
Configuration
Capacitance toleranc (±20%)
Rated capacitance (1200µF)
Rated voltage (4V)
Series name
Type
Dimension table in next page.
CAT.8100Z


Part Details

On this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for PLG0E392MDO1 electronic component.


Information Total 2 Pages
Link URL [ Copy URL to Clipboard ]
Download [ PLG0E392MDO1.PDF Datasheet ]

Share Link :

Electronic Components Distributor


An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists.


SparkFun Electronics Allied Electronics DigiKey Electronics Arrow Electronics
Mouser Electronics Adafruit Newark Chip One Stop


Featured Datasheets

Part NumberDescriptionMFRS
PLG0E392MDO1The function is CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS. NichiconNichicon

Semiconductors commonly used in industry:

1N4148   |   BAW56   |   1N5400   |   NE555   |  

LM324   |   BC327   |   IRF840  |   2N3904   |  



Quick jump to:

PLG0     1N4     2N2     2SA     2SC     74H     BC     HCF     IRF     KA    

LA     LM     MC     NE     ST     STK     TDA     TL     UA    



Privacy Policy   |    Contact Us     |    New    |    Search