DataSheet39.com

What is PLF1D220MCL2?

This electronic component, produced by the manufacturer "Nichicon", performs the same function as "Aluminum Electrolytic Capacitor".


PLF1D220MCL2 Datasheet PDF - Nichicon

Part Number PLF1D220MCL2
Description Aluminum Electrolytic Capacitor
Manufacturers Nichicon 
Logo Nichicon Logo 


There is a preview and PLF1D220MCL2 download ( pdf file ) link at the bottom of this page.





Total 2 Pages



Preview 1 page

No Preview Available ! PLF1D220MCL2 datasheet, circuit

CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
LF Radial Lead Type, Standard
series
Ultra-low ESR, High ripple current.
Load life of 2000 hours at 105°C.
Radial lead type :
Lead free flow soldering condition correspondence.
Compliant to the RoHS directive (2002/95/EC).
LV
High
Voltage
LG
Higher
Capacitance
LS Long Life
LF
Low ESR LE
Specifications
Item
Performance Characteristics
Category Temperature Range 55 to +105°C
Rated Voltage Range
2.5 to 25V
Rated Capacitance Range 6.8 to 1500µF
Capacitance Tolerance
± 20% at 120Hz, 20°C
Tangent of loss angle (tan δ) Less than or equal to the specified value at 120Hz, 20°C
ESR ( 1)
Less than or equal to the specified value at 100kHz, 20°C
Leakage Current ( 2) Less than or equal to the specified value. After 2 minutes' application of rated voltage at 20°C
Temperature Characteristics
(Max.Impedance Ratio)
Z+105°C / Z+20°C 1.25 (100kHz)
Z55°C / Z+20°C 1.25
Endurance
The specifications listed at right shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 2000 hours at 105°C.
Capacitance change
tan δ
ESR ( 1)
Leakage current ( 2)
Within ± 20% of the initial capacitance value ( 3)
150% or less than the initial specified value
150% or less than the initial specified value
Less than or equal to the initial specified value
Damp Heat
(Steady State)
The specifications listed at right shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 1000 hours at 60°C, 90% RH.
Capacitance change
tan δ
ESR ( 1)
Leakage current ( 2)
Within ± 20% of the initial capacitance value ( 3)
150% or less than the initial specified value
150% or less than the initial specified value
Less than or equal to the initial specified value
Resistance to
Soldering Heat
After soldering the capacitor under the soldering conditions
prescribed here as preheat at 150 to 200°C for 60 to 180 seconds
and peak temperature at 265°C for 10 seconds or less, the
capacitor shall meet the specifications listed at right, provided that
its temperature profile is measured at both of terminal ends facing
the soldering side.
Capacitance change
tan δ
ESR ( 1)
Leakage current ( 2)
Within ± 10% of the initial capacitance value ( 3)
130% or less than the initial specified value
130% or less than the initial specified value
Less than or equal to the initial specified value
Marking
Navy blue print on the case top
1 ESR should be measured at both of the terminal ends closest to the capacitor body.
2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120
minutes at 105°C.
3 Initial value : The value before test of examination of resistance to soldering.
Dimensions
Capacitance
Resin coated Case
Voltage(g:4V)
Silvered lead Wire
Type numbering system (Example : 4V 560µF)
1 2 3 4 5 6 7 8 9 10 11 12
P L F 0G 5 6 1 MDO 1
Series
Lot. No.
L+0.5MAX.
φd
15MIN
4MIN
Size code
Configuration
Capacitance toleranc (±20%)
Rated capacitance (560µF)
Rated voltage (4V)
Series name
Type
(mm)
Size φ6.3 × 6L φ6.3 × 9L φ6.3 × 10.5L φ8 × 7L φ8 × 9L φ8 × 12L φ10 × 8L φ10 × 10L φ10 × 13L
φD 6.3 6.3 6.3 8.0 8.0 8.0 10.0 10.0 10.0 Voltage
L 5.5 8.5 10.0 6.5 8.5 11.5 7.5 9.5 12.5
P 2.5 2.5 2.5 3.5 3.5 3.5 5.0 5.0 5.0
φd 0.45 0.6 0.5 0.6 0.6 0.6 0.6 0.6 0.6
V 2.5 4 6.3 10 16
Code e g j A C
Please refer to page 20 about the end seal configulation.
Dimension table in next page.
CAT.8100Z


Part Details

On this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for PLF1D220MCL2 electronic component.


Information Total 2 Pages
Link URL [ Copy URL to Clipboard ]
Download [ PLF1D220MCL2.PDF Datasheet ]

Share Link :

Electronic Components Distributor


An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists.


SparkFun Electronics Allied Electronics DigiKey Electronics Arrow Electronics
Mouser Electronics Adafruit Newark Chip One Stop


Featured Datasheets

Part NumberDescriptionMFRS
PLF1D220MCL2The function is Aluminum Electrolytic Capacitor. NichiconNichicon

Semiconductors commonly used in industry:

1N4148   |   BAW56   |   1N5400   |   NE555   |  

LM324   |   BC327   |   IRF840  |   2N3904   |  



Quick jump to:

PLF1     1N4     2N2     2SA     2SC     74H     BC     HCF     IRF     KA    

LA     LM     MC     NE     ST     STK     TDA     TL     UA    



Privacy Policy   |    Contact Us     |    New    |    Search