|
|
Número de pieza | G215HVN01.0 | |
Descripción | Color TFT-LCD | |
Fabricantes | AUO | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de G215HVN01.0 (archivo pdf) en la parte inferior de esta página. Total 27 Páginas | ||
No Preview Available ! Product Specification
AU OPTRONICS CORPORATION
Preliminary Specification
Final Specification
Module
Model Name
21.5” Color TFT-LCD
G215HVN01.0
G215HVN01.0
Customer
Date
Approved by
Date
Crystal Hsieh
2014/09/05
Checked &
Approved by
Prepared by
Jimmy Tsai
2014/09/05
Note: This Specification is subject to change
without notice.
General Display Business Division / AU
Optronics corporation
document version 1.5
1
1 page Product Specification
AU OPTRONICS CORPORATION
G215HVN01.0
1. Operating Precautions
1) Since front polarizer is easily damaged, pay attention not to scratch it.
2) Be sure to turn off power supply when inserting or disconnecting from input connector.
3) Wipe off water drop immediately. Long contact with water may cause discoloration or spots.
4) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.
5) Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface.
6) Since CMOS LSI is used in this module, take care of static electricity and insure human earth
when handling.
7) Do not open or modify the Module Assembly.
8) In case if a Module has to be put back into the packing container slot after once it was taken
out from the container, take it easily, or the TFT Module may be damaged.
9) At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor tilt the
Interface Connector of the TFT Module.
10) After installation of the TFT Module into an enclosure, do not twist nor bend the TFT Module
even momentary. At designing the enclosure, it should be taken into consideration that no
bending/twisting forces are applied to the TFT Module from outside. Otherwise the TFT
Module may be damaged.
11) Small amount of materials having no flammability grade is used in the LCD module. The LCD
module should be supplied by power complied with requirements of Limited Power Source
(IEC60950 or UL1950), or be applied exemption.
12) Severe temperature condition may result in different luminance, response time and LED life
time.
13) The data on this specification sheet is applicable when LCD module is placed in landscape
position.
14) Continuous displaying fixed pattern may induce image sticking. It is recommended to use
screen saver or shuffle content periodically if fixed pattern is displayed on the screen.
document version 1.5
5
5 Page Product Specification
AU OPTRONICS CORPORATION
G215HVN01.0
3. Functional Block Diagram
The following diagram shows the functional block of this model.
I/F + X-PCB
VLED(+ 12V)
LED driver board
DC/DC
Converter
Gamma
Correction
VDD
(+5V)
LVDS
AUO ASIC
LVDS
Receiver
Timing
Controller
D1
G1
D5760 LED B/L
X-Driver IC
TFT-LCD
1920*(3)*1080
Pixels
G1080
LVDS Connector: JAE (FI-XB30SRL-HF11) or equivalent.
LED Connector: Sin Sheng (MS24049HJ )or equivalent.
document version 1.5
11
11 Page |
Páginas | Total 27 Páginas | |
PDF Descargar | [ Datasheet G215HVN01.0.PDF ] |
Número de pieza | Descripción | Fabricantes |
G215HVN01.0 | Color TFT-LCD | AUO |
G215HVN01.1 | Color TFT-LCD | AUO |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |