DataSheet39.com

What is MP8126?

This electronic component, produced by the manufacturer "MPS", performs the same function as "LNB-Power Supply and Control-Voltage Regulator".


MP8126 Datasheet PDF - MPS

Part Number MP8126
Description LNB-Power Supply and Control-Voltage Regulator
Manufacturers MPS 
Logo MPS Logo 


There is a preview and MP8126 download ( pdf file ) link at the bottom of this page.





Total 13 Pages



Preview 1 page

No Preview Available ! MP8126 datasheet, circuit

MP8126
550mA, 8V-to-14V Input, LNB-Power Supply
and Control-Voltage Regulator
The Future of Analog IC Technology
DESCRIPTION
The MP8126 is a voltage regulator designed to
provide efficient, low-noise power to a satellite
receiver’s RF LNB (Low Noise Block) converter.
It connects using a coaxial cable through a link
that is compatible with the European
EUTELSAT specification (DiSEqC) 1.x that
receives instructions from a dedicated controller.
The MP8126 integrates a current-mode boost
regulator followed by a tracking linear regulator.
The boost regulator provides a clean and quiet
power source that will not contaminate the low-
noise RF signal as it is down-converted to the
receiver. The tracking linear regulator protects
the output against overloads or shorts.
The MP8126 provides a number of features
described in the DiSEqC, including voltage
selection of horizontal or vertical LNB
polarization directions, and selectable VOUT
compensation for substantial voltage drops on
long coaxial cable. In accordance with DiSEqC,
the part can detect a 22kHz signal and output a
shaped signal.
The MP8126 is available in a thermally-
enhanced TSSOP16EP and 24-pin QFN
(4X4mm) packages.
FEATURES
DiSEqC 1.x Compatibility
Up to 550mA Output Current
Programmable Current Limit
8V-to-14V Input Voltage
Boost Converter with Internal Switch
Low-Noise LDO Output
Built-In 22kHz Signal Shaper
1V Line-Drop Compensator
Adjustable Soft-Start Time
POK Indicator
Short-Circuit Protection
Over-Temperature Protection
TSSOP16 Exposed Pad and 24-pin QFN
(4X4mm) Packages
APPLICATIONS
LNB Power Supply and Control for Satellite
Set Top Boxes
All MPS parts are lead-free and adhere to the RoHS directive. For MPS green
status, please visit the MPS website under Products, Quality Assurance.
“MPS” and “The Future of Analog IC Technology” are Registered Trademarks of
Monolithic Power Systems, Inc.
TYPICAL APPLICATION
MP8126 Rev. 1.03
www.MonolithicPower.com
3/28/2014
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2014 MPS. All Rights Reserved.
1

line_dark_gray
MP8126 equivalent
MP8126 – LNB POWER SUPPLY AND CONTROL VOLTAGE REGULATOR
PIN FUNCTIONS
Pin #
TSSOP-16
1
2
3
Pin #
QFN24
22
23, 24
2
44
55
66
77
88
9 10
10 11
11 12
12 13, 14
13 15, 16
14 17
15 19
16 20, 21
1, 3, 9, 18
EP
Name Description
SGND Analog ground.
BYPASS Connect a bypass capacitor for the internal regulator.
VDD
Input supply.
COMP
Compensation pin for Boost regulator (47nF& 4.7k & 470pF is
suggested).
Regulator On/Off Control Input. The output is disabled when this pin
EN
goes low. The converter turns on when this pin goes high. Connect EN
to the input source (through a 100kpull-up resistor if VIN > 6V) for
automatic startup. Do not leave EN floating.
VOUT compensation selection. For voltage drops on the long coaxial
LINEDROP cable. The LDO output increases by 1V when LINEDROP is high,. Do
not leave LINEDROP floating.
POK
Power OK. A high output indicates that LDO output is within ±12% of
nominal value. A low output means that LDO output is outside this
window.
13V/18V
Select 13V or 18V. For output voltage. Select logic HIGH for 18V and
LOW for 13V. Do not leave this pin floating.
EXTM
External Modulation Input. For 22kHz signaling that is internally shaped
and transferred to the output. Tie it to ground if not used.
TCAP
Internal voltage reference for LDO output, A soft-start capacitor can be
connected to this pin to set rise time of the output voltage. The
capacitor should be very close to this pin and SGND, and the route
should keeps far away from any noise like SW copper.
ILIMIT
Output Current Limit Set. Sets the LDO output current limit of LDO.
Program using a resistor from ILIMIT to GND.
VOUT Output Voltage.
VBOOST Internal LDO Input.
BST Internal LDO Driver Supply.
SW
Switching Input. Drain of the internal boost-stage MOSFET. Connect
the power inductor and output rectifier to SW.
PGND Power Ground.
NC Not Connect.
Exposed Pad
Heatsink. Not connected internally. Connect to a metal GND pad for
best results. Do not connect to other pins.
MP8126 Rev. 1.03
www.MonolithicPower.com
3/28/2014
MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited.
© 2014 MPS. All Rights Reserved.
5


line_dark_gray

Preview 5 Page


Part Details

On this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for MP8126 electronic component.


Information Total 13 Pages
Link URL [ Copy URL to Clipboard ]
Download [ MP8126.PDF Datasheet ]

Share Link :

Electronic Components Distributor


An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists.


SparkFun Electronics Allied Electronics DigiKey Electronics Arrow Electronics
Mouser Electronics Adafruit Newark Chip One Stop


Featured Datasheets

Part NumberDescriptionMFRS
MP8125The function is LNB Power Supply and Control Voltage Regulator. MPSMPS
MP8126The function is Cooling Fan Motor. GateGate
MP8126The function is LNB-Power Supply and Control-Voltage Regulator. MPSMPS

Semiconductors commonly used in industry:

1N4148   |   BAW56   |   1N5400   |   NE555   |  

LM324   |   BC327   |   IRF840  |   2N3904   |  



Quick jump to:

MP81     1N4     2N2     2SA     2SC     74H     BC     HCF     IRF     KA    

LA     LM     MC     NE     ST     STK     TDA     TL     UA    



Privacy Policy   |    Contact Us     |    New    |    Search