|
|
Número de pieza | TM080SV-04L01 | |
Descripción | LCD Module | |
Fabricantes | TORiSAN | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de TM080SV-04L01 (archivo pdf) en la parte inferior de esta página. Total 14 Páginas | ||
No Preview Available ! www.DataSheet4UE.cNoGmITNTFEMTEC0RO8ILN0OSGRVSL-P0C4EDLCM0IFO1IDCUALTEIONS
- 20cm (8.0 inch) diagonal
- SVGA resolution (800 x 600 pixels)
m- 6 bits x RGB interface
.co- With CFL backlight unit
- Nonglare surface type
U- Transmissive mode
t4(TENTATIVE)
heeVer.1
Apr. 9, 2001
ataSTottori SANYO Electric Co., Ltd.
.DElectronic Device Business Headquarters
LCD Division
ww3-201, Minami-yoshikata, Tottori, 680-8634 Japan
w TEL: 81-857-21-2941, 1958
FAX: 81-857-21-2162
Department Manager
Engineering Manager
wNSw.. IOWwMA.ODSTAaEKtIaSheet4U.com
1 page [Note 7] Measurement points
1/6Hp 1/2Hp 5/6Hp
1/6Vp
1/2Vp
5/6Vp
12
3
45
Active area
Vp: Total Number of Vertical pixel
[Note 8] Measurement condition
Hp: Total Number of horizontal pixel
(1) Measurement equipment: BM-5A (TOPCON Corp.), Field=2 degree
(2) Ambient temperature Ta: 25 +/- 2 degC
(3) LCD: All pixels are WHITE, VDD=3.3V, fV=60Hz
(4) Measure after 30 minutes of CFL warm up.
(5) IL=(6) mArms with the CFL inverter CXA-L0612A-VJL (TDK).
BACKLIGHT CHARACTERISTICS
ITEM
Lamp voltage
Lamp current
Operating frequency
Start up voltage
Operating life
SYM. CONDITIOS
VL
IL
fL
VS
tOL
MIN
-
(3)
(40)
-
(20000)
TYP
(500)
-
-
-
-
MAX
-
(6)
(65)
(1100)
-
UNIT
Vrms
mArms
kHz
Vrms
Hours
Ta=25 degC
NOTE
at IL=(6)mArms
(Recommended value)
(Recommended value)
at Ta=0 degC
at IL=(6) mArms
[Note 1] Backlight driving conditions (operating frequency fL especially) may interfere
with horizontal frequency fH, causing the beat or flicker on the display.
Therefore the operating frequency fL shall be adjusted in relation to
horizontal frequency fH to avoid interference.
[Note 2] The inverter open voltage should be larger than start up voltage, otherwise backlight
may blinking for a moment after turns on or not be turned on. And this voltage
should be applied to lamp for more than 1 second to start up, otherwise backlight
may not be turned on.
[Note 3] If driving current waveform is asymmetrical, mercury deviation inside of CFL will
incline to one side and consequently abnormal lighting may occur.
To prevent such unfavorable lighting, driving current waveform is asked to have
unbalance rate of less than 10% and wave-height rate of less than 2 +/- 10%.
And this driving waveform shall be confirmed in your system.
Ip
I-p
Current waveform
Unbalance rate = | Ip - I-p | / IL x 100 (%)
Wave-height rate = Ip (or I-p) / IL
Ip : High peak value
I-p : Low peak value
IL : Effective value
Tottori SANYO Electric Co., Ltd. TM080SV-04L01 Ver.1 Page 4/14
5 Page PRECAUTIONS (INSTRUCTIONS FOR SAFE AND PROPER USE)
1. Instructions for safety
(1) Please do not disassemble or modify LCD module to avoid the possibility of
electric shock, damage of electronic components, scratch at display surface and
invasion of foreign particles. In addition, such activity may result in fire accident
due to burning of electronic component.
LCD module disassembled or modified by customer is out of warranty.
(2) Please be careful in handling of LCD module with broken glass.
When the display glass breaks, please pay attention not to injure your fingers. The
display surface has the plastic film attached, which prevents dispersion of glass
pieces, however touching broken edge will injure your fingers. Also CFL (Cold
Cathode Fluorescent Lamp) is made of glass, therefore please pay attention in
the same way.
(3) Please do not touch the fluid flown out of broken display glass.
If the fluid should stick to hand or clothes, wipe off with soap or alcohol
immediately and then wash it with water. If the fluid should get in eyes, wash eyes
immediately with pure water for more than 15 minutes and then consult the doctor.
(4) Please make secure connection of CFL connector.
Please make sure that CFL connector from LCD module is connected with output
connector on inverter circuit securely. Poor connection may cause smoke or fire
accident due to high voltage in circuit. If connection may not be secure, please
switch off the power supply for LCD module and CFL and then make secure
connection.
Please do not make connection with another connector than recommended
mating connector.
(5) CFL contains mercury inside. Please follow regulations or rules established by
local autonomy at its disposal.
(6) Please be careful to electric shock.
Before handling LCD module, please switch off the power supply.
Since high voltage is applied to CFL terminal, cable, connector and inverter circuit
in operation mode, touching them will cause electric shock.
2. Instructions for designing
(1) Mounting of LCD
Please fix LCD module at all mounting flanges shown in this specification for
installation onto system. The used screws should have proper dimensions.
Furthermore, designing of mounting parts should be adequate so that LCD
module is not warped or twisted, to achieve good display quality.
(2) Polarity of power supply for CFL
Please give careful consideration in designing so that each polar of cable should
be connected correctly at assembling (i.e. high voltage side is connected to high
voltage side and low voltage side is connected to low voltage side). Since longer
CFL cable may cause insatiable start-up of CFL and reduction of brightness,
please make cable short as much as possible.
Tottori SANYO Electric Co., Ltd. TM080SV-04L01 Ver.1 Page 10/14
11 Page |
Páginas | Total 14 Páginas | |
PDF Descargar | [ Datasheet TM080SV-04L01.PDF ] |
Número de pieza | Descripción | Fabricantes |
TM080SV-04L01 | LCD Module | TORiSAN |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |