|
|
PDF HT4100F Data sheet ( Hoja de datos )
| Número de pieza | HT4100F | |
| Descripción | Relay | |
| Fabricantes | Htv | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de HT4100F (archivo pdf) en la parte inferior de esta página. Total 8 Páginas | ||
|
No Preview Available !
1. 安全认证:
Safety Standard:
C-UL CQC TUV
HT4100F
Page: 1
2. 接点规格:
Contact Specification:
2.1 接点间隙:
Contact Gap:
最小 0.18 mm。
0.18 mm Minimum.
2.2 接点阻抗:
Contact Resistance
初始值最大 100mΩ；
流通电流 1A、开路测试电压: 6VDC；
使用电压下降法量测。
Maximum 100mΩ at initial value.
Test Current: 1A, Open Circuit Test Voltage: 6VDC.
By using Voltage Drop Method.
2.3 接点容量:
Contact Capacity:
250VAC Cosφ=1，可通过电流为 3 安培。
30VDC ，可通过电流为 3 安培。
3 Amps at 250VAC Cosφ=1.
3 Amps at 30VDC
3. 摄氏 20 度之线圈规格:
Coil Specification at
20 °C:
3.1 额定电压:
Rated Voltage:
3.2 额定电流:( mA± 10%)
Nominal Current:
3.3 额定消耗功率: W
(± 10%.)
Rated Power Consumption:
3.4 线圈阻抗: (Ω± 10%.)
Coil Resistance:
3VDC.
50/67/
120/150
60/45/
25/20
5VDC.
29.9 /40/
72/89
167/125/
70/56
6VDC.
9VDC.
25/33.3/
60/75
16.7/22.5
/40/50
0.15W/0.2W/
0.36W/0.45W
240/180/
100/80
540/400/
220/180
12VDC.
12.5/16.7/
30/37.5
960/720/
400/320
24VDC
6.25/8.3/
15/18.8
3840/2880/
1600/1280
3.5 感动电压:
Pull In Voltage:
(0.2W、0.36W 当电压渐渐施加于继电器时接点之动作电压，为额定电压之 75%
0.15W 为可定电压的 80%)
(0.2W、0.36WContact operating voltage when voltage is gradually applied. It
is 75% of the Rated Voltage 0.15W It is 75% of the Rated Voltage)
_________________________________________________________________________________
深圳市启博电子科技有限公司
深圳市宝安区新湖路华丰科技园华美居商务中心B区412B
Http:// www.cnomron.com
总机：0755-28236318、28236328、28236338
E-mail: [email protected]
传真：0755-28236462
1 page  
5.3.2 储存耐寒性:
Storage Cold
Resistance:
5.4 耐热性:
Heat Resistance:
5.4.1 使用耐热性:
Heat
Resistance in
Use:
5.4.2 储存耐热性:
Storage Heat
Resistance
5.5 耐湿性:
Moisture
Resistance:
6. 端脚特性:
Terminal
Characteristics:
6.1 端脚强度:
Terminal Strength:
6.2 沾锡测试:
Soldering Dip Test:
HT4100F
Page: 5
继电器在恒温箱以-25 ± 2°C 的温度连续保持 72 小时。接着，于常温常湿中消
除水滴 1 至 2 小时以后，进行构造，动作，及绝缘阻抗，耐压的测试，结果需
要符合 SPEC。(在低温时无水滴凝结现象)
Relay should be kept in temperature chamber at -40 ± 2°C for 72 hours.
Then the Relays shall be maintained at standard atmospheric condition for 1
to 2 hours after which measurement shall be made. Construction, Relay
operation, Insulation Resistance and Dielectric Strength shall satisfy the
specification requirements. (No condensation of water drops under low
temperature condition)
继电器操作回路提供定格电压，在接点部份提供定格电流的状态下，在恒温箱
以 75 ± 2°C 的温度连续保持 2 小时后，保持原状态进行继电器动作之测试，结
果必须符合 SPEC。
Relay should be kept in temperature chamber at 75± 2°C for two hours that
rated Voltage should be supplied to Coil while rated Current should be
supplied to Contacts. Such condition shall be maintained while the rated
voltage is supplied to Relay, then Relay shall operate normally.
继电器在恒温箱以 70 ± 2°C 的温度连续保持 16 小时，在常温，常湿状态下，
放置 1-2 小时后，进行构造，动作，及绝缘阻抗，耐压的测试，结果需要符合
SPEC。
Relay should be kept in temperature chamber at 70 ± 2°C for 16 hours. Then
the Relays shall be maintained at standard atmospheric condition for 1 to 2
hours after which measurement shall be made. Construction, Relay
operation, Insulation Resistance and Dielectric Strength shall satisfy the
specification requirements.
继电器以温度 40 ± 2°C 相对温度在 85%环境下连续保持 48 小时，接着，于常
温常湿放置 1-2 小时后，进行构造，动作，及绝缘阻抗，耐压的测试，结果需要
符合 SPEC。
Relay should be kept in temperature chamber at 40 ± 2°C (90~95% RH) for 48
hours. Then the Relays shall be maintained at standard atmospheric
condition for 1 to 2 hours after which measurement shall be made.
Construction, Relay operation, Insulation Resistance, Dielectric Strength shall
satisfy the specification requirements.
在水平方向负重 300 克持续 1 分钟，测试完成后端脚不能有任何的松脱或是弯
曲。
A load of 300g should be applied to the Terminal for one minute in horizontal
direction. There should not be any looseness or bending of Terminals.
温度 230 ± 5°C，时间 3 ± 0.5 秒，浸渍端子前端 3mm，须沾锡面积需达 90%
以上。
The front 3 mm of Terminal should be immersed for 3 ± 0.5 seconds at 230 ±
5°C. Soldered area must be minimum 90% of the soldering surface.
_________________________________________________________________________________
深圳市启博电子科技有限公司
深圳市宝安区新湖路华丰科技园华美居商务中心B区412B
Http:// www.cnomron.com
总机：0755-28236318、28236328、28236338
E-mail: [email protected]
传真：0755-28236462
5 Page | ||
| Páginas | Total 8 Páginas | |
| PDF Descargar | [ Datasheet HT4100F.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| HT4100F | Relay | Htv |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |