MP1583 Datasheet PDF - MPS
Part Number | MP1583 | |
Description | Step-Down Converter | |
Manufacturers | MPS | |
Logo | ||
There is a preview and MP1583 download ( pdf file ) link at the bottom of this page. Total 13 Pages |
Preview 1 page No Preview Available ! MP1583
Step-Down
The Future of Analog IC Technology
DESCRIPTION
The MP1583 is a step -down regulator with a
built-in internal Power MOSFET. It achieves 3A
of continuo us output current over a wide input
supply range with excellent load and line
regulation.
Current mo de operatio n provides f ast transien t
response and eases loop stabilization.
Fault condition protection includes
cycle-by-cycle current limiting a nd thermal
shutdown. An adjustab le soft-start reduces the
stress on the input source at startup. In
shutdown mode the regulator dr aws 20 μA of
supply current.
The MP158 3 requires a minimu m number of
external components, providing a compact
solution.
3A, 23V, 385KHz
Converter
FEATURES
• 3A Output Current
• Programma ble Soft-Start
• 100m Ω Internal Power MOSFET Switch
• Stable with Low ESORutput Ceramic Cpaacitors
• Up to 95% Efficiency
• 20 μA Shutdown Mode
• Fixed 385KHz Frequency
• Thermal Shutdown
• Cycle-by-Cycle Over Current Protection
• Wide 4.75V to 23V Operating Input Range
• Output Adjustable from 1.22V to 21V
• Under-Voltage Lockout
APPLICATIONS
• Distributed Power Systems
• Battery Chargers
• Pre-Regulator for Linear Regulators
“MPS” and “The Future of Analog IC Technology” are Registered Trademarks of
Monolithic Power Systems, Inc.
TYPICAL APPLICATION
INPUT
4.75V to 23V
OPEN =
AUTOMATIC
STARTUP
10μ F
CERAMIC
2 1 10nF
7 IN
EN
BS 3
SW
8
SS
MP1583
FB 5
GND
COMP
46
B330A
10nF
5.6nF
3.9kΩ
15μ H
10.5kΩ
OUTPUT
2.5V
3A
10kΩ
22μ F
CERAMIC
Efficiency Curve
VIN = 10V
100
VOUT=5.0V
90
80 VOUT=2.5V
70 VOUT=3.3V
60
50
0
0.5 1.0 1.5 2.0 2.5 3.0 3.5
LOAD CURRENT (A)
MP1583_EC01
MP1583 Rev. 3.1
6/20/2011
www.MonolithicPower.com
MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited.
© 2011 MPS. All Rights Reserved.
1
http://www.Datasheet4U.com
|
|
MP1583 – 3A, 23V, 385KHz STEP-DOWN CONVERTER
PIN FUNCTIONS (continued)
Pin # Name
7 EN
Description
Enable/UVLO. A voltage greater than 2.71V enables operation. For complete low
current shutdown the EN pin voltage needs to be at less than 900mV. When the
voltage on EN exceeds 1.2V, the internal regulator will be enabled and the soft-start
capacitor will begin to charge. The MP1583 will start switching after the EN pin
voltage reaches 2.71V. There is 7V zener connected between EN and GND. If EN is
driven by external signal, the voltage should never exceed 7V.
8 SS
Soft-Start Control Input. SS controls the soft-start period. Connect a capacitor from SS to GND to
set the soft-start period. To disable the soft-start feature, leave SS unconnected.
OPERATION
The MP15 83 is a current-mode step-down
regulator. It regulates input voltages from 4.75V to
23V down to an output voltage as low as 1.222V,
and is able to supply up to 3A of load current.
The MP1 583 u ses current-mode co ntrol to
regulate the output voltage. The output voltage is
measured at FB thr ough a resistive voltage
divider and amplif ied thr ough the in ternal error
amplifier. The o utput curr ent o f th e
transconductance error amplifier is p resented a t
COMP where a RC net work comp ensates the
regulation control system.
The volta ge a t COMP is compar ed to t he
internally measured switch current t o co ntrol the
output voltage.
The conver ter u ses an internal N-Cha nnel
MOSFET switch to step-down the input voltage to
the regulated output voltage. Since the MOSFET
requires a gate voltag e grea ter th an th e inpu t
voltage, a boost capacitor co nnected be tween
SW an d BS d rives the ga te. T he ca pacitor is
internally charged when SW is low.
An internal 10Ω switch from SW to GND is used
to in sure th at SW is pu lled to GND when SW is
low in order to fully charge the BS capacitor.
IN 2
EN 7
+
1.2V --
--
INTERNAL
REGULATORS
CURRENT
SENSE
AMPLIFIER
+
OSCILLATOR
Σ
SLOPE
COMP
--
40/385KHz
CLK
+
SQ
SHUTDOWN
COMPARATOR
1μ A
RQ
-- CURRENT
COMPARATOR
LOCKOUT
COMPARATOR
7V
1.8V
5V
1 BS
3 SW
2.54V +
+
--
4 GND
FREQUENCY
FOLDBACK
COMPARATOR
-- 0.7V 1.222V + ERROR
AMPLIFIER
5 FB GM = 800μ A/V 6 COMP 8 SS
Figure 1—Functional Block Diagram
MP1583 Rev. 3.1
6/20/2011
www.MonolithicPower.com
MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited.
© 2011 MPS. All Rights Reserved.
5
Preview 5 Page |
Part DetailsOn this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for MP1583 electronic component. |
Information | Total 13 Pages | |
Link URL | [ Copy URL to Clipboard ] | |
Product Image and Detail view | 1. - 3A, 23V, Step-Down Converter [ Learn More ] | |
Download | [ MP1583.PDF Datasheet ] |
Share Link :
Electronic Components Distributor
An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists. |
SparkFun Electronics | Allied Electronics | DigiKey Electronics | Arrow Electronics |
Mouser Electronics | Adafruit | Newark | Chip One Stop |
Featured Datasheets
Part Number | Description | MFRS |
MP158 | The function is (MP151 - MP1510) SINGLE-PHASE GLASS PASSIVATED SILICON BRIDGE RECTIFIER. Rectron Semiconductor | |
MP158 | The function is (MP151 - MP1510) SINGLE-PHASE GLASS PASSIVATED SILICON BRIDGE RECTIFIER. Rectron Semiconductor | |
MP158 | The function is (MP151 - MP1510) 15 Amp Single Phase Bridge Rectifier 50 to 1000 Volts. Micro Commercial Components | |
Semiconductors commonly used in industry:
1N4148 |  
BAW56 |
1N5400 |
NE555 | | ||
Quick jump to:
MP15
1N4
2N2
2SA
2SC
74H
BC
HCF
IRF
KA |