DataSheet39.com

What is MIL-DTL-81706B?

This electronic component, produced by the manufacturer "ETC", performs the same function as "CHEMICAL CONVERSION MATERIALS".


MIL-DTL-81706B Datasheet PDF - ETC

Part Number MIL-DTL-81706B
Description CHEMICAL CONVERSION MATERIALS
Manufacturers ETC 
Logo ETC Logo 


There is a preview and MIL-DTL-81706B download ( pdf file ) link at the bottom of this page.





Total 20 Pages



Preview 1 page

No Preview Available ! MIL-DTL-81706B datasheet, circuit

INCH-POUND
MIL-DTL-81706B
25 October 2004
SUPERSEDING
MIL-DTL-81706A
18 February 2002
DETAIL SPECIFICATION
CHEMICAL CONVERSION MATERIALS
FOR COATING ALUMINUM AND ALUMINUM ALLOYS
This specification is approved for use by all Departments and Agencies of the Department
of Defense.
1. SCOPE
1.1 Scope. This specification covers chemical conversion materials used in the formation
of coatings by the reaction of the material with the surfaces of aluminum and aluminum alloys.
1.2 Classification. The chemical conversion materials and application methods are of the
following types, classes, material forms, and methods.
1.2.1. Types. The chemical conversion materials are of the following types (see 6.2).
Type I – Compositions containing hexavalent chromium.
Type II – Compositions containing no hexavalent chromium.
1.2.2 Classes. The materials, which form protective coatings by chemical reaction with
aluminum and aluminum alloys, are of the following classes (see 6.2).
Class 1A - For maximum protection against corrosion, painted or unpainted.
Class 3 - For protection against corrosion where low electrical resistance is required.
Comments, suggestions, or questions on this document should be addressed to: Commander,
Naval Air Warfare Center Aircraft Division, Code 414100B120-1, Highway 547, Lakehurst,
NJ 08733-5100 or emailed to [email protected]. Since contact information can
change, you may want to verify the currency of this address information using the ASSIST
Online database at www.dodssp.daps.mil.
AMSC N/A
AREA MFFP
Free Datasheet http://www.Datasheet4U.com

line_dark_gray
MIL-DTL-81706B equivalent
MIL-DTL-81706B
3.4 Toxicity. The material and processing baths or solutions shall have no adverse effect
on the health of personnel (see 6.5.2), when used for the intended purpose in accordance with
local process specifications (see 6.1).
3.5 Performance characteristics.
3.5.1 Corrosion resistance. After testing in accordance with 4.5.1 for applicable salt spray
exposure periods specified in table I, the specimens shall show no evidence of corrosion when
compared to unexposed control panels using the naked eye. Areas within 0.25 inch (6.35
millimeters [mm]) from the edges of the panel, the identification markings, and the panel holding
points during processing or salt spray exposure shall not be evaluated. Differences in color
between the test panels and the control panels shall not be cause for rejection.
TABLE I. Schedule for corrosion resistance properties of unpainted chemical films.
Corrosion Resistance
Inspection
Class
Aluminum Alloy To Be
Conversion Coated
Salt Spray
Exposure (Hours)
Qualification
1A
3
2024-T3, 7075-T6
6061-T6
1/ 336
168
Conformance
1A
3
2024-T3
6061-T6
168
168
1/ Exposure time for class 1A, form VI, method D materials shall be 168 hours.
3.5.2 Paint adhesion (wet tape). After application of the epoxy polyamide primer in
accordance with 4.4.4, no intercoat separation shall occur between the paint system, the
conversion coating, or the base metal, when tested in accordance with 4.5.2.
3.5.3 Paint adhesion (wet tape) after repair (applies to nonimmersion methods). After panel
repair and immersion in test fluid as specified in 4.5.3, the scribed panels shall exhibit no peel-
away and be rated at not less than 4A in accordance with ASTM-D3359. There shall be no
blistering of the unscribed coated area.
3.6 Coating weight (class 1A only). When tested in accordance with 4.5.4, type I coating
weight shall be not less than 40 milligrams per square foot (430 milligrams per square meter) of
surface area. Class 1A, type I, form VI, method D coating weight shall be not less than 10
milligrams per square foot of surface area (107.5 milligrams per square meter). Class 1A, type II
coating weight shall be not less than 10 milligrams per square foot of surface area (107.5
milligrams per square meter).
3.7 Contact electrical resistance properties (class 3 only). When tested in accordance with
4.5.5, the contact electrical resistance of aluminum alloy panels treated with class 3 materials
under an applied electrode pressure of 200 pounds per square inch (psi) shall be not greater than
5,000 microhms psi as applied and 10,000 microhms psi after salt spray exposure specified in
4.5.1. Individual readings not greater than 20 percent in excess of the specified maximums shall
5
Free Datasheet http://www.Datasheet4U.com


line_dark_gray

Preview 5 Page


Part Details

On this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for MIL-DTL-81706B electronic component.


Information Total 20 Pages
Link URL [ Copy URL to Clipboard ]
Download [ MIL-DTL-81706B.PDF Datasheet ]

Share Link :

Electronic Components Distributor


An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists.


SparkFun Electronics Allied Electronics DigiKey Electronics Arrow Electronics
Mouser Electronics Adafruit Newark Chip One Stop


Featured Datasheets

Part NumberDescriptionMFRS
MIL-DTL-81706BThe function is CHEMICAL CONVERSION MATERIALS. ETCETC

Semiconductors commonly used in industry:

1N4148   |   BAW56   |   1N5400   |   NE555   |  

LM324   |   BC327   |   IRF840  |   2N3904   |  



Quick jump to:

MIL-     1N4     2N2     2SA     2SC     74H     BC     HCF     IRF     KA    

LA     LM     MC     NE     ST     STK     TDA     TL     UA    



Privacy Policy   |    Contact Us     |    New    |    Search