DataSheet39.com

What is BU7250SG?

This electronic component, produced by the manufacturer "ROHM Semiconductor", performs the same function as "Open Drain Output Low Supply Current CMOS Comparators".


BU7250SG Datasheet PDF - ROHM Semiconductor

Part Number BU7250SG
Description Open Drain Output Low Supply Current CMOS Comparators
Manufacturers ROHM Semiconductor 
Logo ROHM Semiconductor Logo 


There is a preview and BU7250SG download ( pdf file ) link at the bottom of this page.





Total 27 Pages



Preview 1 page

No Preview Available ! BU7250SG datasheet, circuit

Datasheet
Comparators
Input Full Swing, Open Drain Output
Low Supply Current CMOS Comparators
BU7250G BU7250SG BU7253F BU7253SF
General Description
BU7250G/BU7253F are low supply current and open
drain output comparators. BU7250SG/BU7253SF have
an expanded operating temperature range. These
features low operating supply voltage of +1.8V to
+5.5V, Low supply current and extremely low input
bias current.
Features
Low Operating Supply Voltage
Low Supply Current
High Speed Operation
Input Full Swing
Open Drain Output Type
Wide Operating Temperature Range
Applications
Battery Monitor
Mobile Equipments
Limit Comparator
Consumer Electronics
Key Specifications
Operating Supply Voltage:
Single Supply
Split Supply
Supply Current:
BU7250G/BU7250SG
BU7253F/BU7253SF
Temperature Range:
BU7250G/BU7253F
BU7250SG/BU7253SF
Input Offset Current:
Input Bias Current:
+1.8V to +5.5V
±0.9V to ±2.75V
15µA
35µA
-40°C to +85°C
-40°C to +105°C
1pA (Typ)
1pA (Typ)
Packages
SSOP5
SOP8
jW(Typ) x D(Typ) x H(Max)
2.90mm x 2.80mm x 1.25mm
5.00mm x 6.20mm x 1.71mm
Pin Configuration
BU7250G, BU7250SG: SSOP5
IN- 1
VSS 2
IN+ 3
+
5 VDD
4 OUT
BU7253F, BU7253SF: SOP8
OUT1 1
IN1- 2
IN1+ 3
VSS 4
CH1
- ++
CH2
+-
8 VDD
7 OUT2
6 IN2-
5 IN2+
Pin No.
1
2
3
4
5
Pin Name
IN-
VSS
IN+
OUT
VDD
Pin No.
1
2
3
4
5
6
7
8
Pin Name
OUT1
IN1-
IN1+
VSS
IN2+
IN2-
OUT2
VDD
Product structureSilicon monolithic integrated circuit This product has no designed protection against radioactive rays.
www.rohm.com
© 2013 ROHM Co., Ltd. All rights reserved.
TSZ2211114001
1/24
TSZ02201-0RFR1G200450-1-2
4.Dec.2013 Rev.001
http://www.Datasheet4U.com

line_dark_gray
BU7250SG equivalent
BU7250G BU7250SG BU7253F BU7253SF
Datasheet
Description of Electrical Characteristics
Described below are descriptions of the relevant electrical terms used in this datasheet. Items and symbols used are also
shown. Note that item name and symbol and their meaning may differ from those on another manufacturer’s document or
general document.
1. Absolute Maximum Ratings
Absolute maximum rating items indicate the condition which must not be exceeded. Application of voltage in excess of absolute
maximum rating or use out of absolute maximum rated temperature environment may cause deterioration of characteristics.
(1) Supply Voltage (VDD/VSS)
Indicates the maximum voltage that can be applied between the VDD terminal and VSS terminal without
deterioration or destruction of characteristics of internal circuit.
(2) Differential Input Voltage (VID)
Indicates the maximum voltage that can be applied between non-inverting and inverting terminals without damaging
the IC.
(3) Input Common-mode Voltage Range (VICM)
Indicates the maximum voltage that can be applied to the non-inverting and inverting terminals without deterioration
or destruction of electrical characteristics. Input common-mode voltage range of the maximum ratings does not assure
normal operation of IC. For normal operation, use the IC within the input common-mode voltage range characteristics.
(4) Power Dissipation (PD)
Indicates the power that can be consumed by the IC when mounted on a specific board at the ambient temperature 25°C
(normal temperature). As for package product, PD is determined by the temperature that can be permitted by the IC in
the package (maximum junction temperature) and the thermal resistance of the package.
2. Electrical Characteristics
(1) Input Offset Voltage (VIO)
Indicates the voltage difference between non-inverting terminal and inverting terminals. It can be translated into the
input voltage difference required for setting the output voltage at 0 V.
(2) Input Offset Current (IIO)
Indicates the difference of input bias current between the non-inverting and inverting terminals.
(3) Input Bias Current (IB)
Indicates the current that flows into or out of the input terminal. It is defined by the average of input bias currents at
the non-inverting and inverting terminals.
(4) Supply Current (IDD)
Indicates the current that flows within the IC under specified no-load conditions.
(5) Maximum Output Voltage(High) / Maximum Output Voltage(Low) (VOH/VOL)
Indicates the voltage range of the output under specified load condition. It is typically divided into maximum output
voltage High and low. Maximum output voltage high indicates the upper limit of output voltage. Maximum output
voltage low indicates the lower limit.
(6) Large Signal Voltage Gain (AV)
Indicates the amplifying rate (gain) of output voltage against the voltage difference between non-inverting terminal
and inverting terminal. It is normally the amplifying rate (gain) with reference to DC voltage.
Av = (Output voltage) / (Differential Input voltage)
(7) Input Common-mode Voltage Range (VICM)
Indicates the input voltage range where IC normally operates.
(8) Common-mode Rejection Ratio (CMRR)
Indicates the ratio of fluctuation of input offset voltage when the input common mode voltage is changed. It is
normally the fluctuation of DC.
CMRR = (Change of Input common-mode voltage)/(Input offset fluctuation)
(9) Power Supply Rejection Ratio (PSRR)
Indicates the ratio of fluctuation of input offset voltage when supply voltage is changed.
It is normally the fluctuation of DC.
PSRR= (Change of power supply voltage)/(Input offset fluctuation)
(10) Output Source Current/ Output Sink Current (ISOURCE / ISINK)
The maximum current that can be output from the IC under specific output conditions. The output source current
indicates the current flowing out from the IC, and the output sink current indicates the current flowing into the IC.
(11) Output Fall Time (tF)
Indicates the time required for an output voltage step to change from 90% to 10% of its final value.
(12) Propagation Delay Time (L to H) / Propagation Delay Time (H to L) (tPLH / tPHL)
Indicates the time to reach 50% of the output voltage after the step voltage is applied at the input pin.
www.rohm.com
© 2013 ROHM Co., Ltd. All rights reserved.
TSZ2211115001
5/24
TSZ02201-0RFR1G200450-1-2
4.Dec.2013 Rev.001
http://www.Datasheet4U.com


line_dark_gray

Preview 5 Page


Part Details

On this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for BU7250SG electronic component.


Information Total 27 Pages
Link URL [ Copy URL to Clipboard ]
Download [ BU7250SG.PDF Datasheet ]

Share Link :

Electronic Components Distributor


An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists.


SparkFun Electronics Allied Electronics DigiKey Electronics Arrow Electronics
Mouser Electronics Adafruit Newark Chip One Stop


Featured Datasheets

Part NumberDescriptionMFRS
BU7250SGThe function is Open Drain Output Low Supply Current CMOS Comparators. ROHM SemiconductorROHM Semiconductor

Semiconductors commonly used in industry:

1N4148   |   BAW56   |   1N5400   |   NE555   |  

LM324   |   BC327   |   IRF840  |   2N3904   |  



Quick jump to:

BU72     1N4     2N2     2SA     2SC     74H     BC     HCF     IRF     KA    

LA     LM     MC     NE     ST     STK     TDA     TL     UA    



Privacy Policy   |    Contact Us     |    New    |    Search