DataSheet39.com

What is ML1000605D?

This electronic component, produced by the manufacturer "IRF", performs the same function as "HIGH RELIABILITY RADIATION HARDENED LOW POWER DC-DC CONVERTER".


ML1000605D Datasheet PDF - IRF

Part Number ML1000605D
Description HIGH RELIABILITY RADIATION HARDENED LOW POWER DC-DC CONVERTER
Manufacturers IRF 
Logo IRF Logo 


There is a preview and ML1000605D download ( pdf file ) link at the bottom of this page.





Total 17 Pages



Preview 1 page

No Preview Available ! ML1000605D datasheet, circuit

HIGH RELIABILITY
RADIATION HARDENED
LOW POWER
DC-DC CONVERTER
PD-97806
ML1000605D
100V Input, Dual Output
Description
The ML-Series of isolated DC-DC converters for space
applications are low power radiation hardened high
reliability devices designed for hostile radiation
environments such as those encountered by geostationary
earth orbit satellites, deep space probes and communication
systems. Features include small size, high efficiency,
low weight, and a good tolerance to total ionizing dose,
single event effects, and environmental stresses such
as temperature extremes, mechanical shock, and
vibration. All components are fully derated to meet the
requirements of EEE-INST-002 (NASA) and ECSS-Q-
30-11A (ESA). Extensive documentation including worst
case analysis, radiation susceptibility, thermal analysis,
stress analysis, and reliability analysis are available.
The ML-Series converter has two outputs – one positive
and one negative - each is independently regulated via
linear post regulators. The outputs are sequenced
during turn-on and turn-off such that negative output
comes up first at turn-on and stays up at turn-off until the
positive output has decreased. The ML-series converters
incorporate a fixed frequency flyback power converter
and internal EMI filter that meets the requirements for
most major satellite power buses. The converter includes
isolated On/Off telecommand with associated status
telemetry. The converter also includes input under
voltage shut-down functionality.
Due to the linear post regulation of the outputs, the ML-
Series is well suited for use in RF-applications where
low noise, high output voltage accuracy, and high CS
attenuation is required.
Each converter is provided as a complete board
assembly for installation into the host equipment chassis.
The board is conformal coated (except for mating
surfaces) and is mounted in the host chassis using
screws. The board outline is L x W x H: 70mm x 50mm x
18mm. The weight is less than 50 grams.
www.irf.com
Features
n Total Dose > 100 krad(Si)
n SEE > 82 MeV.cm2/mg
n Low Weight < 50 grams
n 97V to 103V DC Input Range
n O/P 1: +6.0V (up to 500mA)
n O/P 2: -5.0V (up to 100mA)
n Output Ripple: < 1mVrms (100Hz - 50MHz)
n CS Rejection Input to Outputs: > 90dB
(50Hz - 1.0MHz)
n 10M@ 100VDC Isolation
n Input Under-Voltage Protection
n Meets Conducted Emission Requirements of
Major Power Buses:
100Hz - 100kHz: 80dBuArms
100kHz - 10MHz: -20dB/decade
10MHz - 50MHz: 40dBuArms
n Short Circuit and Overload Protection
n Meets Derating Requirements of EEE-INST
002 and ECSS-Q-30-11A
n Isolated On/Off Control via High Level Pulse
Command (Latching Relay)
n Status Telemetry (Relay Contact Type)
n Workmanship Per IPC-A610 Class 3
n Board is Coated with ARATHANE-5750
Applications
n Low Power RF Systems (like LNA) on-board
Satellites
Non-flight versions of the ML-Series converters
are available for system development purposes.
Variations in electrical specifications and
screening to meet custom requirements can be
accommodated.
1
04/22/13
http://www.Datasheet4U.com

line_dark_gray
ML1000605D equivalent
ML1000605D
(100V Input, Dual Output)
Electrical Performance Characteristics (continued)
Parameter
Condition
Conditions
-40°C Tc +75°C
VIN = 100V DC ± 0.5%, CL = 0µF
unless otherwise specified
EMC conducted
susceptibility
(Line rejection)
IOUT = 100% rated load
1 Primary power sine wave injection of
2Vp-p, 100Hz to 1MHz, Note 1
Electromagnetic Interference
(EMI), conducted emission
(CE)
Isolation
1
1
Device Weight
IOUT = 100% rated load, Notes 1, 7
Input to Output, any potential to
telecommand input and any potential to
telemetry output, test @ 100VDC
Failure Rate
MIL-HDBK-217F2, SF, 35°C, Note 8
Limits
Min Nom Max
Unit
96 110
dB
Limits per Figures 4 and 5
10 M
50 g
60 FITs
Notes: Specification and Electrical Performance Characteristics Tables
1. Parameter is tested as part of design characterization or after design changes. Thereafter, parameter shall
be guaranteed to the limits specified.
2. Guaranteed for a D.C. to 50MHz bandwidth. Tested using a 10.7MHz bandwidth.
3. Load current step transition time 10 µs.
4. Recovery time is measured from the initiation of the transient to where VOUT has returned to within ±1% of
its steady state value.
5. Turn-on delay time from application of telecommand pulse to the point where Output 2 = 98% of nominal
output voltage.
6. Capacitive load may be any value from 0 to the maximum limit without compromising the output sequencing
performance. A capacitive load in excess of the maximum limit may influence the output sequencing
performance and start-up time, converter operation and dc performance will remain intact.
7. The switching frequency and 1st and 2nd harmonic of the input ripple is tested on every unit.
8. MIL-HDBK-217F2 stress-dependent method is used with 2 exceptions: For soldering a fixed failure rate at
0.035FIT is used and for power MOSFETs the dissipated power (instead of rated power) is used for the Pr
parameter. 1 FIT is 1 failure in 109 hours.
9. The converter meets full derating per EEE-INST-002 and ECSS-Q-30-11A with the following exception: For
Schottky diode JANS1N5819 a maximum derated junction temperature of +110°C. For EEE-INST-002 it is
required that ceramic capacitors with a voltage stress below 10V shall be rated for minimum 100V - in the
product such capacitors is rated for 50V minimum.
10. Although operation temperatures between -55°C to +100°C and -40°C to+75°C is guaranteed, no
parameter limits are specified.
Electrical Performance Characteristics - Definition of Conditions
Condition Definition
Comment
1 BOL @ +25°C interface temperature
Initial setting
2 BOL @ -40°C to +75°C interface temperature Initial setting and worst case temperature variation
3 EOL @ -40°C to +75°C interface temperature Worst case performance including initial setting,
temperature variation, aging and radiation degradation
www.irf.com
5
http://www.Datasheet4U.com


line_dark_gray

Preview 5 Page


Part Details

On this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for ML1000605D electronic component.


Information Total 17 Pages
Link URL [ Copy URL to Clipboard ]
Download [ ML1000605D.PDF Datasheet ]

Share Link :

Electronic Components Distributor


An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists.


SparkFun Electronics Allied Electronics DigiKey Electronics Arrow Electronics
Mouser Electronics Adafruit Newark Chip One Stop


Featured Datasheets

Part NumberDescriptionMFRS
ML1000605DThe function is HIGH RELIABILITY RADIATION HARDENED LOW POWER DC-DC CONVERTER. IRFIRF

Semiconductors commonly used in industry:

1N4148   |   BAW56   |   1N5400   |   NE555   |  

LM324   |   BC327   |   IRF840  |   2N3904   |  



Quick jump to:

ML10     1N4     2N2     2SA     2SC     74H     BC     HCF     IRF     KA    

LA     LM     MC     NE     ST     STK     TDA     TL     UA    



Privacy Policy   |    Contact Us     |    New    |    Search