DataSheet39.com

What is MIC38C44?

This electronic component, produced by the manufacturer "Micrel Semiconductor", performs the same function as "BiCMOS Current-Mode PWM Controllers".


MIC38C44 Datasheet PDF - Micrel Semiconductor

Part Number MIC38C44
Description BiCMOS Current-Mode PWM Controllers
Manufacturers Micrel Semiconductor 
Logo Micrel Semiconductor Logo 


There is a preview and MIC38C44 download ( pdf file ) link at the bottom of this page.





Total 11 Pages



Preview 1 page

No Preview Available ! MIC38C44 datasheet, circuit

MIC38C42/3/4/5
Micrel, Inc.
MIC38C42/3/4/5
BiCMOS Current-Mode PWM Controllers
General Description
The MIC38C4x are fixed frequency, high performance, cur-
rent-mode PWM controllers. Micrel’s BiCMOS devices are
pin compatible with 384x bipolar devices but feature several
improvements.
Undervoltage lockout circuitry allows the ’42 and ’44 versions
to start up at 14.5V and operate down to 9V, and the ’43 and
’45 versions start at 8.4V with operation down to 7.6V. All
versions operate up to 20V.
When compared to bipolar 384x devices operating from a
15V supply, start-up current has been reduced to 50µAtypical
and operating current has been reduced to 4.0 mA typical.
Decreased output rise and fall times drive larger MOSFETs,
and rail-to-rail output capability increases efficiency, espe-
cially at lower supply voltages. The MIC38C4x also features
a trimmed oscillator discharge current and bandgap refer-
ence.
The MIC38C4x denotes 8-pin plastic DIP, SOIC, and MSOP
packages. MIC384Cx-1 denotes 14-pin plastic DIP and
SOIC packages. 8-pin devices feature small size, while 14-
pin devices separate the analog and power connections for
improved perfomance and power dissipation.
Features
• Fast 40ns output rise and 30ns output fall times
• –40°C to +85°C temperature range
meets UC284x specifications
• High-performance, low-power BiCMOS Process
• Ultralow start-up current (50µA typical)
• Low operating current (4mA typical)
• CMOS outputs with rail-to-rail swing
• ≥ 500kHz current-mode operation
• Trimmed 5V bandgap reference
• Pin-for-pin compatible with UC3842/3843/3844/3845(A)
• Trimmed oscillator discharge current
• UVLO with hysteresis
• Low cross-conduction currents
Applications
• Current-mode, off-line, switched-mode power supplies
• Current-mode, dc-to-dc converters.
• Step-down “buck” regulators
• Step-up “boost” regulators
• Flyback, isolated regulators
• Forward converters
• Synchronous FET converters
For fast rise and fall times and higher output drive, refer to
the MIC38HC4x.
Functional Diagram
VDD
7 (12)
VREF
8 (14)
RT/CT
4 (7)
FB
2 (3)
2.5V
35V
5V
Reference
Oscillator
2R
R
UVLO
*
T Q
S
R
Q
(VD)
(11)
OUT
6 (10)
(PGND)
(8)
*
COMP GND* (AGND) ISNS
1 (1)
5 (9) 3 (5)
( ) pins are on MIC38C4x-1 (14-lead) versions only
* MIC38C4x, (8-lead) versions only
MIC38C42, MIC38C43 (96% max. duty cycle) versions only
MIC38C44, MIC38C45 (50% max. duty cycle) versions only
Micrel, Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel + 1 (408) 944-0800 • fax + 1 (408) 474-1000 • http://www.micrel.com
September 2007
1
M9999-091107
http://www.Datasheet4U.com

line_dark_gray
MIC38C44 equivalent
MIC38C42/3/4/5
Micrel, Inc.
Parameter
Test Conditions
Min Typ Max Units
Current Sense
Gain
Notes 2, 3
2.85 3.0 3.15 V/V
MaximumThreshold
PSRR
Input Bias Current
VCOMP = 5V, Note 2
12 ≤ VDD ≤ 18V, Note 2
0.9 1 1.1
70
–0.1 –2
V
dB
µA
Delay to Output
120 250
ns
Output
RDS(ON) High
RDS(ON) Low
Rise Time
Fall Time
Undervoltage Lockout
ISOURCE = 200mA
ISINK = 200mA
TA = 25°C, CL = 1nF
TA = 25°C, CL = 1nF
20 Ω
11 Ω
40 80 ns
30 60 ns
Start Threshold
MIC38C42/4
13.5 14.5 15.5
V
MIC38C43/5
7.8 8.4 9.0
V
Minimum Operating Voltage
MIC38C42/4
8 9 10 V
MIC38C43/5
7.0 7.6 8.2
V
Pulse Width Modulator
Maximum Duty Cycle
MIC38C42/3
94 96
%
MIC38C44/5
46 50
%
Minimum Duty Cycle
0%
Total Standby Current
Start-Up Current
VDD = 13V for MIC38C42/44
VDD = 7.5V for MIC38C43/45
Operating Supply Current
VFB = VISNS = 0V
Zener Voltage (VDD)
IDD = 25mA, Note 6
Note 1: These parameters, although guaranteed, are not 100% tested in production.
Note 2: Parameter measured at trip point of latch with VEA = 0.
Note 3: Gain defined as:
A
=
∆VPIN1
VTH (ISNS)
;
0
VTH
(ISNS)
0.8V
50 200 µA
4.0 6.0 mA
30 37
V
Note 4: Adjust VDD above the start threshold before setting at 15V.
Note 5: Output frequency equals oscillator frequency for the MIC38C42 and MIC38C43. Output frequency for the MIC38C44, and
MIC38C45 equals one half the oscillator frequency.
Note 6: On 8-pin version, 20V is maximum input on pin 7, as this is also the supply pin for the output stage. On 14-pin version, 40V is
maximum for pin 12 and 20V maximum for pin 11.
September 2007
5
M9999-091107
http://www.Datasheet4U.com


line_dark_gray

Preview 5 Page


Part Details

On this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for MIC38C44 electronic component.


Information Total 11 Pages
Link URL [ Copy URL to Clipboard ]
Download [ MIC38C44.PDF Datasheet ]

Share Link :

Electronic Components Distributor


An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists.


SparkFun Electronics Allied Electronics DigiKey Electronics Arrow Electronics
Mouser Electronics Adafruit Newark Chip One Stop


Featured Datasheets

Part NumberDescriptionMFRS
MIC38C42The function is BiCMOS Current-Mode PWM Controllers. Micrel SemiconductorMicrel Semiconductor
MIC38C42The function is BiCMOS Current-Mode PWM Controllers. Micrel SemiconductorMicrel Semiconductor
MIC38C42-1BMThe function is BiCMOS Current-Mode PWM Controllers. Micrel SemiconductorMicrel Semiconductor

Semiconductors commonly used in industry:

1N4148   |   BAW56   |   1N5400   |   NE555   |  

LM324   |   BC327   |   IRF840  |   2N3904   |  



Quick jump to:

MIC3     1N4     2N2     2SA     2SC     74H     BC     HCF     IRF     KA    

LA     LM     MC     NE     ST     STK     TDA     TL     UA    



Privacy Policy   |    Contact Us     |    New    |    Search