What is A4953?

This electronic component, produced by the manufacturer "Allegro", performs the same function as "(A4952 / A4953) Full-Bridge DMOS PWM Motor Drivers".

A4953 Datasheet PDF - Allegro

Part Number A4953
Description (A4952 / A4953) Full-Bridge DMOS PWM Motor Drivers
Manufacturers Allegro 
Logo Allegro Logo 

There is a preview and A4953 download ( pdf file ) link at the bottom of this page.

Total 11 Pages

Preview 1 page

No Preview Available ! A4953 datasheet, circuit

A4952 and A4953
Full-Bridge DMOS PWM Motor Drivers
Features and Benefits
• Low RDS(on) outputs
• Overcurrent protection (OCP)
Motor short protection
Motor lead short to ground protection
Motor lead short to battery protection
• Low Power Standby mode
• Adjustable PWM current limit
• Synchronous rectification
• Internal undervoltage lockout (UVLO)
• Crossover-current protection
• Fault output (A4952 only)
• Selectable retry (A4952 only)
10-pin MSOP
with exposed thermal pad
(LY package)
Designed for pulse width modulated (PWM) control of DC
motors, the A4952 and A4953 are capable of peak output
currents to ±2 A and operating voltages to 40 V.
Input terminals are provided for use in controlling the speed and
direction of a DC motor with externally applied PWM control
signals. Internal synchronous rectification control circuitry is
provided to lower power dissipation during PWM operation.
Internal circuit protection includes overcurrent protection,
motor lead short to ground or supply, thermal shutdown with
hysteresis, undervoltage monitoring of VBB, and crossover-
current protection.
The A4952 is provided in a low-profile 10-pin MSOP package
(suffix LY) and the A4953 is provided in a low-profile
8-pin SOICN package (suffix LJ). Both packages have an
exposed thermal pad, and are lead (Pb) free, with 100% matte tin
leadframe plating.
8-pin SOICN
with exposed thermal pad
(LJ package)
Not to scale
Functional Block Diagram
A4952 only
A4952 only
÷ 10
Load Supply
A4952-DS, Rev. 2
Free Datasheet

A4953 equivalent
A4952 and
Full-Bridge DMOS PWM Motor Drivers
Functional Description
Device Operation
The A4952 and A4953 are designed to operate DC motors. The
output drivers are all low-RDS(on) , N-channel DMOS drivers
that feature internal synchronous rectification to reduce power
dissipation. The current in the output full bridge is regulated with
fixed off-time pulse width modulated (PWM) control circuitry.
The IN1 and IN2 inputs allow two-wire control for the bridge.
Protection circuitry includes internal thermal shutdown, and pro-
tection against shorted loads, or against output shorts to ground
or supply. Undervoltage lockout prevents damage by keeping the
outputs off until the driver has enough voltage to operate nor-
Standby Mode
Low Power Standby mode is activated when both input (INx)
pins are low for longer than 1 ms. Low Power Standby mode
disables most of the internal circuitry, including the charge pump
and the regulator. When the A4952/A4953 is coming out of
standby mode, the charge pump should be allowed to reach its
regulated voltage (a maximum delay of 200 μs) before any PWM
commands are issued to the device.
Internal PWM Current Control
Initially, a diagonal pair of source and sink FET outputs are
enabled and current flows through the motor winding and the
optional external current sense resistor, RS. When the voltage
across RS equals the comparator trip value, then the current sense
comparator resets the PWM latch. The latch then turns off the
sink and source FETs (Mixed Decay mode).
The maximum value of current limiting is set by the selection of
RSx and the voltage at the VREF pin. The transconductance func-
tion is approximated by the maximum value of current limiting,
ITripMAX (A), which is set by:
ITripMAX =
where VREF is the input voltage on the VREF pin (V) and RS is
the resistance of the sense resistor (Ω) on the LSS terminal.
Overcurrent Protection
In the A4952, a current monitor will protect the IC from damage
due to output shorts. The internal Overcurrent Protection (OCP)
has the following features:
• Fault Output (FLTn pin). If a short is detected, the open drain
FLTn output signal goes low.
• Retry Input (RTRY pin). Sets the action taken by the IC to re-
spond to an OCP fault. If the RTRY pin is tied to GND, then the
outputs will be turned-on again after a 2-ms timeout, to check
if a fault condition remains. If the RTRY pin is left open, then
the fault will be latched, and the IC will disable the outputs. The
fault latch can only be cleared by coming out of Low Power
Standby mode or by cycling the power to VBB.
Note: The A4953 overcurrent protection behaves in the same
manner but the fault is latched and can only be reset by putting
the device into standby mode or by cycling the power to VBB.
During OCP events, Absolute Maximum Ratings may be
exceeded for a short period of time before the device latches.
If the die temperature increases to approximately 160°C, the full
bridge outputs will be disabled until the internal temperature falls
below a hysteresis, TTSDhys , of 20°C. Internal UVLO is present
on VBB to prevent the output drivers from turning-on below the
UVLO threshold.
The braking function is implemented by driving the device in
Slow Decay mode, which is done by applying a logic high to both
inputs, after a bridge-enable Chop command (see PWM Control
Truth Table). Because it is possible to drive current in both direc-
tions through the DMOS switches, this configuration effectively
shorts-out the motor-generated BEMF, as long as the Chop com-
mand is asserted. The maximum current can be approximated by
VBEMF / RL. Care should be taken to ensure that the maximum
ratings of the device are not exceeded in worse case braking situ-
ations: high speed and high-inertia loads.
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
Free Datasheet


Preview 5 Page

Part Details

On this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for A4953 electronic component.

Information Total 11 Pages
Link URL [ Copy URL to Clipboard ]
Download [ A4953.PDF Datasheet ]

Share Link :

Electronic Components Distributor

An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists.

SparkFun Electronics Allied Electronics DigiKey Electronics Arrow Electronics
Mouser Electronics Adafruit Newark Chip One Stop

Featured Datasheets

Part NumberDescriptionManufacturers
A4950The function is Full-Bridge DMOS PWM Motor Driver.Allegro MicroSystems
Allegro MicroSystems
A4952The function is (A4952 / A4953) Full-Bridge DMOS PWM Motor Drivers.Allegro
A4953The function is (A4952 / A4953) Full-Bridge DMOS PWM Motor Drivers.Allegro

Semiconductors commonly used in industry:

1N4148   |   BAW56   |   1N5400   |   NE555   |  

LM324   |   BC327   |   IRF840  |   2N3904   |  

Quick jump to:

A495     1N4     2N2     2SA     2SC     74H     BC     HCF     IRF     KA    

LA     LM     MC     NE     ST     STK     TDA     TL     UA    

Privacy Policy   |    Contact Us     |    New    |    Search