K9F1G08U0C Datasheet PDF - Samsung
Part Number | K9F1G08U0C | |
Description | FLASH MEMORY | |
Manufacturers | Samsung | |
Logo | ||
There is a preview and K9F1G08U0C download ( pdf file ) link at the bottom of this page. Total 36 Pages |
Preview 1 page No Preview Available ! K9F1G08B0C
K9F1G08U0C
Advance
FLASH MEMORY
K9F1G08X0C
INFORMATION IN THIS DOCUMENT IS PROVIDED IN RELATION TO SAMSUNG PRODUCTS,
AND IS SUBJECT TO CHANGE WITHOUT NOTICE.
NOTHING IN THIS DOCUMENT SHALL BE CONSTRUED AS GRANTING ANY LICENSE,
EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE,
TO ANY INTELLECTUAL PROPERTY RIGHTS IN SAMSUNG PRODUCTS OR TECHNOLOGY. ALL
INFORMATION IN THIS DOCUMENT IS PROVIDED
ON AS "AS IS" BASIS WITHOUT GUARANTEE OR WARRANTY OF ANY KIND.
1. For updates or additional information about Samsung products, contact your nearest Samsung office.
2. Samsung products are not intended for use in life support, critical care, medical, safety equipment, or similar
applications where Product failure could result in loss of life or personal or physical harm, or any military or
defense application, or any governmental procurement to which special terms or provisions may apply.
* Samsung Electronics reserves the right to change products or specification without notice.
Samsung Confidential
1
Free Datasheet http://www.datasheetlist.com/
|
|
K9F1G08B0C
K9F1G08U0C
Advance
FLASH MEMORY
PIN DESCRIPTION
Pin Name
I/O0 ~ I/O7
Pin Function
DATA INPUTS/OUTPUTS
The I/O pins are used to input command, address and data, and to output data during read operations. The
I/O pins float to high-z when the chip is deselected or when the outputs are disabled.
COMMAND LATCH ENABLE
CLE The CLE input controls the activating path for commands sent to the command register. When active high,
commands are latched into the command register through the I/O ports on the rising edge of the WE signal.
ADDRESS LATCH ENABLE
ALE The ALE input controls the activating path for address to the internal address registers. Addresses are
latched on the rising edge of WE with ALE high.
CHIP ENABLE
CE The CE input is the device selection control. When the device is in the Busy state, CE high is ignored, and
the device does not return to standby mode in program or erase operation.
READ ENABLE
RE The RE input is the serial data-out control, and when active drives the data onto the I/O bus. Data is valid
tREA after the falling edge of RE which also increments the internal column address counter by one.
WRITE ENABLE
WE The WE input controls writes to the I/O port. Commands, address and data are latched on the rising edge of
the WE pulse.
WRITE PROTECT
WP The WP pin provides inadvertent program/erase protection during power transitions. The internal high volt-
age generator is reset when the WP pin is active low.
READY/BUSY OUTPUT
R/B
The R/B output indicates the status of the device operation. When low, it indicates that a program, erase or
random read operation is in process and returns to high state upon completion. It is an open drain output and
does not float to high-z condition when the chip is deselected or when outputs are disabled.
Vcc
POWER
VCC is the power supply for device.
Vss GROUND
N.C
NO CONNECTION
Lead is not internally connected.
Note : Connect all VCC and VSS pins of each device to common power supply outputs.
Do not leave VCC or VSS disconnected.
Samsung Confidential
5
Free Datasheet http://www.datasheetlist.com/
Preview 5 Page |
Part DetailsOn this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for K9F1G08U0C electronic component. |
Information | Total 36 Pages | |
Link URL | [ Copy URL to Clipboard ] | |
Download | [ K9F1G08U0C.PDF Datasheet ] |
Share Link :
Electronic Components Distributor
An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists. |
SparkFun Electronics | Allied Electronics | DigiKey Electronics | Arrow Electronics |
Mouser Electronics | Adafruit | Newark | Chip One Stop |
Featured Datasheets
Part Number | Description | MFRS |
K9F1G08U0A | The function is FLASH MEMORY. Samsung semiconductor | |
K9F1G08U0A | The function is 128M x 8 Bit / 256M x 8 Bit NAND Flash Memory. Samsung semiconductor | |
K9F1G08U0B | The function is Flash Memory. Samsung Electronics | |
Semiconductors commonly used in industry:
1N4148 |  
BAW56 |
1N5400 |
NE555 | | ||
Quick jump to:
K9F1
1N4
2N2
2SA
2SC
74H
BC
HCF
IRF
KA |