BK1088 Datasheet PDF - BEKEN
Part Number | BK1088 | |
Description | (BK1086 / BK1088) BROADCAST AM/FM/SW/LW RADIO RECEIVER | |
Manufacturers | BEKEN | |
Logo | ||
There is a preview and BK1088 download ( pdf file ) link at the bottom of this page. Total 30 Pages |
Preview 1 page No Preview Available ! BK1086/88
BROADCAST AM/FM/SW/LW RADIO RECEIVER
Features
Worldwide 64~108 MHz FM band
support
Worldwide 520~1710kHz AM band
support
SW band support(2.3-21.85MHz,
BK1088 only)
LW band support(153-279kHz,BK1088
only)
Automatic gain control(AGC)
Automatic frequency control(AFC)
Digital FM stereo decoder
Automatic FM stereo/mono blend
Automatic noise suppression
50us/75us de-emphasis
RDS/RBDS decoder
2.4 ~ 5.5 V supply voltage
Wide range reference clock support
32.768KHz crystal oscillator
4x4 mm 24-pin QFN package
Applications
Table and portable radios
CD/DVD players
Modules
General Description
The BK1086/88 AM/FM receiver employs a
low-IF architecture, mixed signal image
rejection and all digital demodulation
technology. The station scan of BK1086/88
searches radio stations based on both the
channel RSSI estimation and signal quality
assessment, increases the number of receivable
stations while avoids false stops. BK1086/88
enables FM/AM/SW/LW radio reception with
low power, small board space and minimum
number of external component.
24 23 22 21 20 19
GND 1
18 VA
FMI 2
RFGND 3
GND PAD
17 GND
16 LOUT
AMI 4
BK1086/88
15 ROUT
GND 5
14 GND
NC 6
13 VD
7 8 9 10 11 12
QFN 24 Pin Assignments (Top View)
Functional Block Diagram
FM ANT
FM LNA
MIXER
RFGND
AM LNA
MIXER
I
PGA
Q
PGA
ADC
ADC
RDS
DSP
DAC LOUT
DAC ROUT
32.768KHz
VDD
AUTO
TUNE
0/90
DPLL
APLL
REG BK1086/88
GPIO
SDIO
SEN
SCLK
VIO
Rev.1.0
Copyright©2010 by Beken Corporation
BK1086/88
Beken Confidential. Information contained herein is covered under non-disclosure agreement (NDA).
Free Datasheet http://www.datasheet4u.net/
|
|
2.4 Stereo Audio Processing
The output of the FM demodulator is a
stereo multiplexed (MPX) signal. MPX
signal format consists of left + right
(L+R) audio, left – right (L–R) audio, a
19 kHz pilot tone, and RDS data.
The BK1086/88 has integrated stereo
decoder automatically decodes the MPX
signal. The 0 to 15 kHz (L+R) signal is
the mono output of the FM tuner. Stereo
is generated from the (L+R), (L-R), and
a 19 kHz pilot tone. The pilot tone is
used as a reference to recover the (L-R)
signal. Separate left and right channels
are obtained by adding and subtracting
the (L+R) and (L-R) signals,
respectively. Adaptive noise suppression
is employed to gradually combine the
stereo left and right audio channels to a
mono (L+R) audio signal as the signal
quality degrades to maintain optimum
sound fidelity under varying reception
conditions. The signal level range over
which the stereo to mono blending
occurs can be adjusted by setting the
BLNDADJ [1:0] register. Stereo/mono
status can be monitored with the ST
register bit and mono operation can be
forced with the MONO register bit and
stereo operation can be forced with the
STEREO register bit.
BK1086/88 uses pre-emphasis and de-
emphasis to improve the signal-to-noise
ratio of FM receivers by reducing the
effects of high frequency interference
and noise. When the FM signal is
transmitted, a pre-emphasis filter is
applied to accentuate the high audio
frequencies. All FM receivers
incorporate a de-emphasis filter which
attenuates high frequencies to restore a
BK1086/88
flat frequency response. Two time
constants, 50 or 75μs, are used in
various regions. The de-emphasis time
constant is programmable with the DE
bit. High-fidelity stereo digital-to-analog
converters (DACs) drive analog audio
signals onto the LOUT and ROUT pins.
The audio output may be muted with the
DMUTE bit. Volume can be adjusted
digitally with the VOLUME [4:0] bits.
The soft mute feature is available to
attenuate the audio outputs and minimize
audible noise in very weak signal
conditions. The soft mute attack and
decay rate can be adjusted with the
SMUTER [1:0] bits where 00 is the
fastest setting. The soft mute attenuation
level can be adjusted with the SMUTEA
[1:0] bits where 00 is the most
attenuated. The soft mute disable
(DSMUTE) bit may be set high to
disable this feature.
2.5 Seek/Tune System
In FM mode, channel spacing of 10, 50,
100 or 200 kHz is selected with bits
SPACE [1:0]. The channel is selected
with bits CHAN [14:0]. The bottom of
the band is set to 64 MHz, 76 MHz or 87
MHz with the bits BAND [1:0]. The
tuning operation begins by setting the
TUNE bit. After tuning completes, the
seek/tune complete (STC) bit will be set
and the RSSI level is available by
reading bits RSSI [6:0]. The TUNE bit
must be set low after the STC bit is set
high in order to prepare for the next tune
operation and clear the STC bit. Seek
tuning searches up or down for a channel
with RSSI greater than the seek
threshold set with the SEEKTH [6:0]
bits and SNR greater than the SNR
threshold set with the SKSNR [6:0] bits.
Proprietary and Confidential
Page 5 of 30
Free Datasheet http://www.datasheet4u.net/
Preview 5 Page |
Part DetailsOn this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for BK1088 electronic component. |
Information | Total 30 Pages | |
Link URL | [ Copy URL to Clipboard ] | |
Download | [ BK1088.PDF Datasheet ] |
Share Link :
Electronic Components Distributor
An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists. |
SparkFun Electronics | Allied Electronics | DigiKey Electronics | Arrow Electronics |
Mouser Electronics | Adafruit | Newark | Chip One Stop |
Featured Datasheets
Part Number | Description | MFRS |
BK1080 | The function is FM Receiver IC. BEKEN | |
BK1081 | The function is FM STEREO TRANSMITTER. Beken | |
BK1085 | The function is FM STEREO TRANSMITTER. Beken | |
Semiconductors commonly used in industry:
1N4148 |  
BAW56 |
1N5400 |
NE555 | | ||
Quick jump to:
BK10
1N4
2N2
2SA
2SC
74H
BC
HCF
IRF
KA |