DX1000 Datasheet PDF - Pelco
Part Number | DX1000 | |
Description | Digital Video Recorder Operation Manual | |
Manufacturers | Pelco | |
Logo | ||
There is a preview and DX1000 download ( pdf file ) link at the bottom of this page. Total 24 Pages |
Preview 1 page No Preview Available ! ®
DX1000 Series
Digital Video Recorder
Installation/
Operation Manual
C680M-G (7/01)
Pelco • 3500 Pelco Way • Clovis, CA 93612-5699 USA • www.pelco.com
In North America and Canada: Tel (800) 289-9100 • FAX (800) 289-9150
International Customers: Tel +1(559) 292-1981 • FAX +1(559) 348-1120
Free Datasheet http://www.datasheet4u.com/
|
|
WARNING: Adequate
ventilation is required for
proper operation of the
DVR. Allow two inches of
space above the unit and on
each side for air circulation.
1 Connect cameras to the CAMERA INPUT connectors (BNC) on the rear of the DVR.
Refer to Table A for video coaxial cable distances.
2 Connect a monitor to the MONITOR OUTPUT connector (BNC) on the rear of the DVR.
Refer to Table A for video coaxial cable distances.
3 To save data from the DVR, connect a peripheral recording device to the VIDEO
PRINTER OUTPUT connector (BNC) on the rear of the DVR. Refer to Table A for
video coaxial cable distances.
Table A. Video Coaxial Cable Requirements
Cable Type*
Maximum Distance
RG59/U
RG6/U
RG11/U
750 ft (229 m)
1,000 ft (305 m)
1,500 ft (457 m)
* Minimum cable requirements:
75 ohms impedance
All-copper center conductor
All-copper braided shield with 95% braid coverage
4 Connect alarm inputs and alarm relay output as follows:
a. Inputs – Connect wiring (not supplied) to your alarms (not supplied). Two wires
are required for each alarm. You can have one alarm for each camera.
b. Output – Connect wiring (not supplied) to a 12 VDC light or buzzer (not supplied).
Two wires are required.
c. Bring the alarm input and output wiring to the back of the DVR and thread the
wiring through the Induced Voltage Protector (supplied). Loop the wiring over the
voltage protector and thread it through the voltage protector a second time.
d. Connect the alarm input wires to the SENSOR connectors.
e. Connect the light or buzzer to the ALARM output connectors.
5 Connect the recorder to power.
a. Place the NTSC/PAL switch in the proper mode.
b. If applicable, connect the 230 VAC adapter to the end of the power cord. Plug in
the power cord.
c. Turn on the DVR. When the recorder is turned on for the first time, the Help
screens will appear on the monitor. To bypass the Help screens, press the Play/
Pause button.
6 Turn on the cameras and monitor. The DVR begins recording the cameras.
IMPORTANT– If you have any unused camera inputs, the video appears washed out.
The degree of washout depends on how many inputs have no cameras connected to
them. If only one camera is connected, the video is completely washed out. When you
program the DVR (step 9), you must turn off any unused camera inputs. Video
will then appear normal.
7 Go to Time Menu in the Programming section and set the time and date.
8 Initialize the DVR. Refer to the instructions on a separate sheet.
This is a necessary step as the DVR may not operate properly during playback and
search operation if there are conflicts in the date and time. Initializing the DVR erases
all data on the hard disk drive so that you start with a clean file management system
for your recordings.
9 Proceed to the Programming section to set up the recording parameters and enter a
password (optional).
Pelco Manual C680M-G (7/01)
5
Free Datasheet http://www.datasheet4u.com/
Preview 5 Page |
Part DetailsOn this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for DX1000 electronic component. |
Information | Total 24 Pages | |
Link URL | [ Copy URL to Clipboard ] | |
Download | [ DX1000.PDF Datasheet ] |
Share Link :
Electronic Components Distributor
An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists. |
SparkFun Electronics | Allied Electronics | DigiKey Electronics | Arrow Electronics |
Mouser Electronics | Adafruit | Newark | Chip One Stop |
Featured Datasheets
Part Number | Description | MFRS |
DX1000 | The function is Digital Video Recorder Operation Manual. Pelco | |
Semiconductors commonly used in industry:
1N4148 |  
BAW56 |
1N5400 |
NE555 | | ||
Quick jump to:
DX10
1N4
2N2
2SA
2SC
74H
BC
HCF
IRF
KA |