MXT2482SXA Datasheet PDF - ETC
Part Number | MXT2482SXA | |
Description | 450 kHz Synchronous Rectified Step-Down Converter | |
Manufacturers | ETC | |
Logo | ||
There is a preview and MXT2482SXA download ( pdf file ) link at the bottom of this page. Total 10 Pages |
Preview 1 page No Preview Available ! MXT2482SX/A
2-2.5A, 23V, 450 kHz Synchronous Rectified Step-Down Converter
DESCRIPTION
The MXT2482SX is amonolithic synchronous buck regulator. The device integrates 150mΩ
MOSFETS that provide 2A continuous load current over a wide operating input voltage of
4.5 to 23V. Current mode control provides fast transient response and cycle-by-cycle
current limit.
An adjustable soft-start prevents inrush current at turn-on. In shutdown mode, the supply
current drops below 1µA.
This device, available in an 8-pin SOIC package, provides a very compact system solution
with minimal reliance on external components.
PACKAGE REFERENCE FEATURES
. • 2-2.5A Output Current
. • Wide 4.5-23V Operating Input Range
. • Integrated 150mΩ Power MOSFET Switches
. • Output Adjustable from from 0.925 to 20V
. • Up to 95% Efficiency
. • Programmable Soft-Start
. • Stable with Low ESR Ceramic Output Capacitors
. • Fixed 450KHz Frequency
. • Cycle-by-Cycle Over Current Protection
. • Input Under Voltage Lockout
. • Thermally Enhanced 8-Pin SOIC/SOIC-E Package
APPLICATIONS
. • Distributed Power Systems
. • Networking Systems
. • FPGA, DSP, ASIC Power Supplies
. • Green Electronics/ Appliances
. • Notebook Computers
1/1
Free Datasheet http://www.datasheet4u.com/
|
|
MXT2482SX/A
2-2.5A, 23V, 450 kHz Synchronous Rectified Step-Down Converter
OPERATION
FUNCTIONAL DESCRIPTION
The MXT2482SX is a synchronous rectified, current-mode, step-down regulator. It regulates
input voltages from 4.5V to 23V down to an output voltage as low as 0.925V, and supplies up
to 2A of load current. The MXT2482SX uses current-mode control to regulate the output voltage.
The output voltage is measured at FB through a resistive voltage divider and amplified
through the internal transconductance error amplifier. The voltage at the COMP pin is
compared to the switch current measured internally to control the output voltage.
The converter uses internal N-Channel MOSFET switches to step-down the input voltage to
the regulated output voltage. Since the high side MOSFET requires a gate voltage greater
than the input voltage, a boost capacitor connected between SW and BS is needed to drive
the high side gate. The boost capacitor is charged from the internal 5V rail when SW is low.
When the MXT2482SX FB pin exceeds 20% of the nominal regulation voltage of 0.925V, the
over voltage comparator is tripped and the COMP pin and the SS pin are discharged to GND,
forcing the high-side switch off.
Figure 1 – Functional Block Diagram
5/5
Free Datasheet http://www.datasheet4u.com/
Preview 5 Page |
Part DetailsOn this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for MXT2482SXA electronic component. |
Information | Total 10 Pages | |
Link URL | [ Copy URL to Clipboard ] | |
Download | [ MXT2482SXA.PDF Datasheet ] |
Share Link :
Electronic Components Distributor
An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists. |
SparkFun Electronics | Allied Electronics | DigiKey Electronics | Arrow Electronics |
Mouser Electronics | Adafruit | Newark | Chip One Stop |
Featured Datasheets
Part Number | Description | MFRS |
MXT2482SX | The function is 450 kHz Synchronous Rectified Step-Down Converter. ETC | |
MXT2482SXA | The function is 450 kHz Synchronous Rectified Step-Down Converter. ETC | |
Semiconductors commonly used in industry:
1N4148 |  
BAW56 |
1N5400 |
NE555 | | ||
Quick jump to:
MXT2
1N4
2N2
2SA
2SC
74H
BC
HCF
IRF
KA |