|
|
PDF HIP4082 Data sheet ( Hoja de datos )
| Número de pieza | HIP4082 | |
| Descripción | 80V/ 1.25A Peak Current H-Bridge FET Driver | |
| Fabricantes | Intersil Corporation | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de HIP4082 (archivo pdf) en la parte inferior de esta página. Total 14 Páginas | ||
|
No Preview Available !
Data Sheet
September 30, 2015
HIP4082
FN3676.5
80V, 1.25A Peak Current H-Bridge
FET Driver
The HIP4082 is a medium frequency, medium voltage
H-Bridge N-Channel MOSFET driver IC, available in 16 lead
plastic SOIC (N) and DIP packages.
Specifically targeted for PWM motor control and UPS
applications, bridge based designs are made simple and
flexible with the HIP4082 H-bridge driver. With operation up
to 80V, the device is best suited to applications of moderate
power levels.
Similar to the HIP4081, it has a flexible input protocol for
driving every possible switch combination except those
which would cause a shoot-through condition. The
HIP4082’s reduced drive current allows smaller packaging
and it has a much wider range of programmable dead times
(0.1 to 4.5s) making it ideal for switching frequencies up to
200kHz. The HIP4082 does not contain an internal charge
pump, but does incorporate non-latching level-shift
translation control of the upper drive circuits.
This set of features and specifications is optimized for
applications where size and cost are important. For
applications needing higher drive capability the HIP4080A
and HIP4081A are recommended.
Features
• Independently Drives 4 N-Channel FET in Half Bridge or
Full Bridge Configurations
• Bootstrap Supply Max Voltage to 95VDC
• Drives 1000pF Load in Free Air at 50°C with Rise and Fall
Times of Typically 15ns
• User-Programmable Dead Time (0.1 to 4.5s)
• DIS (Disable) Overrides Input Control and Refreshes
Bootstrap Capacitor when Pulled Low
• Input Logic Thresholds Compatible with 5V to 15V Logic
Levels
• Shoot-Through Protection
• Undervoltage Protection
• Pb-Free Plus Anneal Available (RoHS Compliant)
Applications
• UPS Systems
• DC Motor Controls
• Full Bridge Power Supplies
• Switching Power Amplifiers
• Noise Cancellation Systems
• Battery Powered Vehicles
• Peripherals
• Medium/Large Voice Coil Motors
• Related Literature
- TB363, Guidelines for Handling and Processing
Moisture Sensitive Surface Mount Devices (SMDs)
1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 | Copyright Intersil Americas LLC 2003-2006, 2015. All Rights Reserved
Intersil (and design) is a trademark owned by Intersil Corporation or one of its subsidiaries.
All other trademarks mentioned are the property of their respective owners.
1 page  
HIP4082
Absolute Maximum Ratings
Thermal Information
Supply Voltage, VDD . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to 16V
Logic I/O Voltages . . . . . . . . . . . . . . . . . . . . . . . -0.3V to VDD +0.3V
Voltage on AHS, BHS . . . . . -6V (Transient) to 80V (25°C to 150°C)
Voltage on AHS, BHS . . . . . -6V (Transient) to 70V (-55°C to150°C)
Voltage on AHB, BHB . . . . . . . . VAHS, BHS -0.3V to VAHS, BHS +VDD
Voltage on ALO, BLO. . . . . . . . . . . . . . . . . . VSS -0.3V to VDD +0.3V
Voltage on AHO, BHO . . . VAHS, BHS -0.3V to VAHB, BHB +0.3V Input
Current, DEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -5mA to 0mA
Phase Slew Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20V/ns
NOTE: All voltages are relative VSS unless otherwise specified.
Operating Conditions
Thermal Resistance
JA (°C/W)
SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
115
DIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
90
Maximum Power Dissipation. . . . . . . . . . . . . . . . . . . . . . . . See Curve
Storage Temperature Range . . . . . . . . . . . . . . . . . .-65°C to +150°C
Operating Max. Junction Temperature. . . . . . . . . . . . . . . . . . +150°C
Lead Temperature (Soldering 10s) . . . . . . . . . . . . . . . . . . . . +300°C
(For SOIC - Lead Tips Only))
Supply Voltage, VDD . . . . . . . . . . . . . . . . . . . . . . . . . +8.5V to +15V
Voltage on VSS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -1.0V to +1.0V
Voltage on AHB, BHB . . . . . . . . VAHS, BHS +7.5V to VAHS, BHS +VDD
Input Current, DEL . . . . . . . . . . . . . . . . . . . . . . . . . -4mA to -100A
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
Electrical Specifications
PARAMETER
VDD = VAHB = VBHB = 12V, VSS = VAHS = VBHS = 0V, RDEL = 100K
SYMBOL
TEST CONDITIONS
TJ = +25°C
MIN TYP MAX
TJ = -55°C
TO +150°C
MIN MAX
UNITS
SUPPLY CURRENTS & UNDER VOLTAGE PROTECTION
VDD Quiescent Current
VDD Operating Current
AHB, BHB Off Quiescent Current
AHB, BHB On Quiescent Current
AHB, BHB Operating Current
AHS, BHS Leakage Current
VDD Rising Undervoltage Threshold
VDD Falling Undervoltage Threshold
Undervoltage Hysteresis
IDD
IDDO
IAHBL, IBHBL
IAHBH, IBHBH
IAHBO, IBHBO
IHLK
VDDUV+
VDDUV-
UVHYS
All inputs = 0V, RDEL = 100K
All inputs = 0V, RDEL = 10K
f = 50kHz, no load
50kHz, no load, RDEL = 10k
AHI = BHI = 0V
AHI = BHI = VDD
f = 50kHz, CL = 1000pF
VAHS = VBHS = 80V
VAHB = VBHB = 96
VDD = Not Connected
1.2 2.3 3.5 0.85 4
2.2 4.0 5.5 1.9 6.0
1.5 2.6 4.0 1.1 4.2
2.5 4.0 6.4 2.1 6.6
0.5 1.0 1.5 0.4 1.6
65 145 240 40 250
.65 1.1 1.8 .45 2.0
- - 1.0 - -
mA
mA
mA
mA
mA
A
mA
A
6.8 7.6 8.25 6.5 8.5
6.5 7.1 7.8 6.25 8.1
0.17 0.4 0.75 0.15 0.90
V
V
V
AHB, BHB Undervoltage Threshold
VHBUV Referenced to AHS & BHS
5 6.0 7 4.5 7.5
V
INPUT PINS: ALI, BLI, AHI, BHI, & DIS
Low Level Input Voltage
High Level Input Voltage
Input Voltage Hysteresis
Low Level Input Current
High Level Input Current
TURN-ON DELAY PIN DEL
Dead Time
VIL Full Operating Conditions
VIH Full Operating Conditions
- - 1.0 - 0.8
2.5 -
- 2.7
- 35 - - -
V
V
mV
IIL
VIN = 0V, Full Operating Conditions
-145 -100 -60 -150 -50
A
IIH
VIN = 5V, Full Operating Conditions
-1 - +1 -10 +10 A
TDEAD
RDEL = 100K
RDEL = 10K
2.5 4.5 8.0 2.0 8.5
0.27 0.5 0.75 0.2 0.85
s
s
5 FN3676.5
September 30, 2015
5 Page 
Performance Curves (Continued)
104
VDD = 15V
1000
VDD = 12V
VDD = 9V
HIP4082
90
85
80
75
100
0
10 20 30 40 50 60 70 80 90 100
DEAD TIME RESISTANCE (k)
FIGURE 16. DEAD-TIME vs DEL RESISTANCE AND BIAS
SUPPLY (VDD) VOLTAGE
70 100
50 0
50
TEMPERATURE (°C)
100
FIGURE 17. MAXIMUM OPERATING PEAK AHS/BHS
VOLTAGE vs TEMPERATURE
150
11 FN3676.5
September 30, 2015
11 Page | ||
| Páginas | Total 14 Páginas | |
| PDF Descargar | [ Datasheet HIP4082.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| HIP4080 | 80V/2.5A Peak/ High Frequency Full Bridge FET Driver | Intersil Corporation |
| HIP4080A | High Frequency Full Bridge FET Driver | Intersil Corporation |
| HIP4080IB | 80V/2.5A Peak/ High Frequency Full Bridge FET Driver | Intersil Corporation |
| HIP4080IP | 80V/2.5A Peak/ High Frequency Full Bridge FET Driver | Intersil Corporation |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |