DataSheet39.com

What is AH1898?

This electronic component, produced by the manufacturer "Diodes", performs the same function as "PROGRAMMABLE MICROPOWER OMNIPOLAR HALL-EFFECT SWITCH".


AH1898 Datasheet PDF - Diodes

Part Number AH1898
Description PROGRAMMABLE MICROPOWER OMNIPOLAR HALL-EFFECT SWITCH
Manufacturers Diodes 
Logo Diodes Logo 


There is a preview and AH1898 download ( pdf file ) link at the bottom of this page.





Total 11 Pages



Preview 1 page

No Preview Available ! AH1898 datasheet, circuit

AH1898
PROGRAMMABLE MICROPOWER OMNIPOLAR HALL-EFFECT SWITCH
Description
The AH1898 is a micropower magnetic range selectable (Bop/Brp)
Omnipolar Hall effect switch IC with internal pull up and pull down
capability, designed for portable and battery powered consumer
equipment such as cellular phones and portable PCs. To support
battery powered equipment and low voltage microcontrollers, the
AH1898 can operate over the supply range of 1.6V to 3.6V and uses
a hibernating clocking system to minimize the power consumption.
The average supply current is only 4.3µA typical at 1.80V. The
AH1898 has an 8kV ESD rating on the supply and output pins. To
minimize PCB space the AH1898 is packaged in the small
CSP package (0.81mm x 0.81mm typical).
The output is activated with either a north or south pole of sufficient
magnetic field strength. The user can select one of two magnetic
sensitivity bands via the BSEL pin without the addition of any external
components allowing a flexible but small solution. The band select
can be hardwired or be changed on the fly via a logic source such as
a micro-controller. When the magnetic flux density (B) perpendicular
to the package is larger than operate point (Bop), the output will be
turned on (pulled low) and held until B is lower than release point
(Brp). The output will remain off when there is no magnetic field.
Pin Assignments
(Top View)
(Bottom View)
U-WLB0808-4
Features
Omnipolar Operation (North or South pole)
Programmable Operate and Release Points
Supply Voltage of 1.6V to 3.6V
Micropower Operation
Chopper Stabilized Design Provides
Superior Temperature Stability
Minimal Switch Point Drift
Enhanced Immunity to Physical Stress
No External Pull-up Resistors Required
Good RF Noise Immunity
-40°C to +85°C Operating Temperature
8kV Human Body Model ESD Capability
Miniature U-WLB0808-4 (CSP 0.81mm x 0.81mm typical)
Totally Lead-Free & Fully RoHS Compliant (Notes 1 & 2)
Halogen and Antimony Free. “Green” Device (Note 3)
Applications
http://www.D
Open and Close Detect for Cellular Phones
Holster or Cover Detect for Cellular Phones and Tablet PCs
Cover or Display Switch in Portable PCs
Digital Still, Video Cameras and Handheld Gaming Consoles
Proximity and Position Switches
a
t
Notes:
1. No purposely added lead. Fully EU Directive 2002/95/EC (RoHS) & 2011/65/EU (RoHS 2) compliant.
2. See http://www.diodes.com for more information about Diodes Incorporated’s definitions of Halogen- and Antimony-free, "Green" and Lead-free.
3. Halogen- and Antimony-free "Green” products are defined as those which contain <900ppm bromine, <900ppm chlorine (<1500ppm total Br + Cl)
and <1000ppm antimony compounds.
AH1898
Document number: DS36028 Rev. 1 - 2
1 of 11
www.diodes.com
February 2013
© Diodes Incorporated
d
a

line_dark_gray
AH1898 equivalent
AH1898
Application Note
Applications Circuit One – Low Band
Connecting the BSEL pin to ground permanently configures the AH1898 into its high sensitivity mode, requiring a reduced magnetic flux density
to activate its output (Low Band).
Applications Circuit Two – High Band
Connecting the BSEL pin to VDD or to a voltage greater than 1.4V or leaving the BSEL pin unconnected configures the AH1898 into its low
sensitivity mode, requiring a higher magnetic flux density to activate its output (High Band).
http://www.DataS
Applications Circuit Three – Adjustable Sensitivity
To enhance flexibility within the application, the sensitivity can be adjusted with a standard logic signal allowing it to be controlled by a micro-
controller or a logic source. This allows the sensitivity to be changed within the application without a hardware change. Whenever the sensitivity
band selection is changed, the band selection changeover should be allowed to complete for the output to be valid.
AH1898
Document number: DS36028 Rev. 1 - 2
5 of 11
www.diodes.com
February 2013
© Diodes Incorporated
d
a


line_dark_gray

Preview 5 Page


Part Details

On this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for AH1898 electronic component.


Information Total 11 Pages
Link URL [ Copy URL to Clipboard ]
Download [ AH1898.PDF Datasheet ]

Share Link :

Electronic Components Distributor


An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists.


SparkFun Electronics Allied Electronics DigiKey Electronics Arrow Electronics
Mouser Electronics Adafruit Newark Chip One Stop


Featured Datasheets

Part NumberDescriptionMFRS
AH1891The function is MINIATURE MICROPOWER OMNIPOLAR HALL EFFECT SWITCH. DiodesDiodes
AH1892The function is PROGRAMMABLE MICROPOWER OMNIPOLAR HALL-EFFECT SENSOR SWITCH. DiodesDiodes
AH1893The function is HIGH SENSITIVITY MICROPOWER OMNIPOLAR HALL-EFFECT SWITCH. DiodesDiodes

Semiconductors commonly used in industry:

1N4148   |   BAW56   |   1N5400   |   NE555   |  

LM324   |   BC327   |   IRF840  |   2N3904   |  



Quick jump to:

AH18     1N4     2N2     2SA     2SC     74H     BC     HCF     IRF     KA    

LA     LM     MC     NE     ST     STK     TDA     TL     UA    



Privacy Policy   |    Contact Us     |    New    |    Search