DataSheet39.com

What is AYF53?

This electronic component, produced by the manufacturer "Panasonic", performs the same function as "Connectors".


AYF53 Datasheet PDF - Panasonic

Part Number AYF53
Description Connectors
Manufacturers Panasonic 
Logo Panasonic Logo 


There is a preview and AYF53 download ( pdf file ) link at the bottom of this page.





Total 5 Pages



Preview 1 page

No Preview Available ! AYF53 datasheet, circuit

AYF53
For FPC/FFC*
FPC connectors
(0.5mm pitch)
Back lock
Y5B/Y5BW
Series
New
Y5B
Low profile and space saving body of 1.0
mm high and 3.20 mm deep (3.70 mm
including the lever)
Y5B and Y5BW can have a minimum of
four and two contacts respectively,
contributing to the miniaturization and
thickness reduction of target equipment.
Applicable FPC shapes
Structure to lock
through-holes and
notches on both ends
of the FPC with
holding contacts
Y5BW
Compliance with RoHS Directive
FEATURES
• Low profile, space saving back lock
type with improved lever operability
• Mechanical design freedom achieved
by top and bottom double contacts
• Wide selection, including a type with
a small number of contacts
1.00
3.20
Unit: mm
4 contacts (Y5B: minimum)
• Wiring patterns can be located
underneath the connector.
• Man-hours for assembly can be
reduced by delivering the connectors
with their levers opened.
• Y5BW features advanced
functionality, including a structure to
temporarily hold the FPC and a higher
holding force.
The FPC holding contacts located on
both ends of the connector facilitate
positioning of FPC and further enhance
the FPC holding force.
www.DataSheet.co.kr
ORDERING INFORMATION
AYF 5 3
53: FPC Connector 0.5 mm pitch
(Back lock)
Number of contacts (2 digits)
Function
3: Top and bottom double contacts (Y5B)
6: Top and bottom double contacts, lock holding type (Y5BW)
Surface treatment (Contact portion / Terminal portion)
5: Au plating/Au flash plating (Ni barrier)
5
With notches With through-holes
(1) The holding contacts lock the FPC by its through-holes or
notches, allowing users to confirm the completion of the
FPC insertion operation.
(2) The inserted FPC can be temporarily held until the lever is
closed.
(3) When the lever is closed, the holding contacts lock the
FPC by its through-holes and notches, enhancing the FPC
holding force.
* (Y5BW is compatible with FPC only.)
APPLICATIONS
A wide range of digital equipment,
including mobile phones, PCs, DSCs,
and DVCs. Ideal for their touch panels
and LCD backlights, which require
connectors with a small number of
contacts.
PRODUCT TYPES
Height
Y5B
Number of contacts
Part number
Y5BW
Number of contacts
Part number
4 AYF530435 2 AYF530265
5 AYF530535 3 AYF530365
6 AYF530635 4 AYF530465
8 AYF530835 6 AYF530665
10 AYF531035 8 AYF530865
1.0 mm
12 AYF531235 10 AYF531065
14 AYF531435 12 AYF531265
16 AYF531635 14 AYF531465
24 AYF532435 22 AYF532265
28 AYF532835 26 AYF532665
50 AYF535035 48 AYF534865
Notes: 1. Order unit;
For mass production: in 1-inner carton (1-reel) units
Samples for mounting check: in 50-connector units. Please contact our sales office.
2. Please contact are sales office for connectors having a number of contacts other than those listed above.
Packing
Inner carton (1-reel)
Outer carton
5,000 pieces
10,000 pieces
panasonic-electric-works.net/ac
Datasheet pdf - http://www.DataSheet4U.net/

line_dark_gray
AYF53 equivalent
NOTES FOR USING FPC CONNECTORS (Common)
PC board design
Design the recommended foot pattern in
order to secure the mechanical strength
in the soldered areas of the terminal.
FPC and equipment design
Design the FPC based on the
recommended dimensions to ensure the
required connector performance.
In addition, carefully check the equipment
design and take required measures for
the equipment to prevent the FPC from
being removed subsequent to a fall,
vibration, or other impact due to the FPC
size, weight, or the reaction force of the
routed FPC.
Connector mounting
In case the connector is picked up by
chucking during mounting, an excessive
mounter chucking force may deform the
molded or metal part of the connector.
Consult us in advance if chucking is to be
applied.
Soldering
1) Manual soldering.
• Due to the low profile, if an excessive
amount of solder is applied to this
product during manual soldering, the
solder may creep up to near the contact
points, or interference by solder may
cause imperfect contact.
• Make sure that the soldering iron tip is
heated within the temperature and time
limits indicated in the specifications.
• Flux from the solder wire may adhere to
the contact surfaces during soldering
operations. After soldering, carefully
check the contact surfaces and clean off
any flux before use.
• Be aware that a load applied to the
connector terminals while soldering may
displace the contact.
• Thoroughly clean the iron tip.
2) Reflow soldering
• Screen-printing is recommended for
printing paste solder.
Y3FT/Y3F/Y3B/Y5F/Y5B/Y5BW
To determine the relationship between
the screen opening area and the PC
board foot pattern area, refer to the
diagrams in the recommended
patterns for PC boards and metal
masks when setting.
Note that excess solder on the
terminals prevents complete insertion
of the FPC, and that excess solder on
the metal clips prevents the lever from
rotating.
Y5S
Note that excess solder inhibits the
slider lock operation.
Terminal Paste solder
PC board foot pattern
Y3FT/Y3F/Y3B/Y5S/Y5F/Y5B/Y5BW
Screen thickness of 120µm is recom-
mended for paste solder printing.
• Consult us when using a screen-printing
thickness other than that recommended.
• Depending on the size of the connector
being used, self alignment may not be
possible. Accordingly, carefully position
the terminal with the PC board pattern.
• The recommended reflow temperature
profile is given in the figure below
Recommended reflow temperature
profile
Y3FT/Y3F/Y3B/Y5B/Y5BW
Temperature
260°C
230°C
180°C
150°C
Upper limit (Soldering heat resistance)
Lower limit (Solder wettability)
Peak temperature
Preheating
www.DataSheet.co.kr
60 to 120 sec.
220°C
200°C
25 sec.
70 sec.
Y5S
Temperature
250°C
200°C
180°C
150°C
Time
Peak temperature
Preheating Min. 200°C,
60 to 120 sec. 70 sec.
Y5F
Temperature
260°C
200°C
180°C
150°C
Time
Peak temperature
Preheating Min. 200°C,
60 to 120 sec. 70 sec.
Time
• The temperature is measured on the
surface of the PC board near the
connector terminal.
• Some solder and flux types may cause
serious solder creeping. Take the solder
and flux characteristics into consideration
when setting the reflow soldering
conditions.
• When performing reflow soldering on
the back of the PC board after reflow
soldering the connector, secure the
connector using, for example, an
adhesive. (Double reflow soldering on the
same side is possible)
3) Reworking on a soldered portion
• Finish reworking in one operation.
• For reworking of the solder bridge, use
a soldering iron with a flat tip. Do not add
flux, otherwise, the flux may creep to the
contact parts.
• Use a soldering iron whose tip
temperature is within the temperature
range specified in the specifications.
Do not drop the product or handle
carelessly. Otherwise, the terminals
may become deformed due to
excessive force or the solderability
during reflow soldering may degrade.
Don’t open/close the lever or insert/
remove an FPC until the connector is
soldered. Forcibly applied external
pressure on the terminals can weaken
the adherence of the terminals to the
molded part or cause the terminals to
lose their evenness. In addition, do
not insert an FPC into the connector
before soldering the connector.
When cutting or bending the PC
board after mounting the connector,
be careful that the soldered sections
are subjected to excessive forces.
Do not the soldered areas to be subjected to forces
Other Notes
When coating the PC board after
soldering the connector to prevent the
deterioration of insulation, perform the
coating in such a way so that the coating
does not get on the connector.
The connectors are not meant to be used
for switching.
For other details, please verify with
the product specification sheets.
panasonic-electric-works.net/ac
Datasheet pdf - http://www.DataSheet4U.net/


line_dark_gray

Preview 5 Page


Part Details

On this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for AYF53 electronic component.


Information Total 5 Pages
Link URL [ Copy URL to Clipboard ]
Download [ AYF53.PDF Datasheet ]

Share Link :

Electronic Components Distributor


An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists.


SparkFun Electronics Allied Electronics DigiKey Electronics Arrow Electronics
Mouser Electronics Adafruit Newark Chip One Stop


Featured Datasheets

Part NumberDescriptionMFRS
AYF53The function is Connectors. PanasonicPanasonic

Semiconductors commonly used in industry:

1N4148   |   BAW56   |   1N5400   |   NE555   |  

LM324   |   BC327   |   IRF840  |   2N3904   |  



Quick jump to:

AYF5     1N4     2N2     2SA     2SC     74H     BC     HCF     IRF     KA    

LA     LM     MC     NE     ST     STK     TDA     TL     UA    



Privacy Policy   |    Contact Us     |    New    |    Search