DataSheet39.com

What is CM2031?

This electronic component, produced by the manufacturer "ON Semiconductor", performs the same function as "HDMI Receiver Port Protection and Interface Device".


CM2031 Datasheet PDF - ON Semiconductor

Part Number CM2031
Description HDMI Receiver Port Protection and Interface Device
Manufacturers ON Semiconductor 
Logo ON Semiconductor Logo 


There is a preview and CM2031 download ( pdf file ) link at the bottom of this page.





Total 18 Pages



Preview 1 page

No Preview Available ! CM2031 datasheet, circuit

HDMI Receiver Port Protectionwww.DataSheet4U.com
and Interface Device
CM2031
Features
• HDMI 1.3 compliant
• Supports thin dielectric and 2-layer boards
• Minimizes TMDS skew with 0.05pF matching
• Long HDMI cable support with integrated I2C
accelerator
• Active termination and slew rate limiting for CEC
• Supports direct connection to CEC microcontroller
• Integrated I2C level shifting to CMOS level
including low logic level voltages
• Integrated ±8kV ESD protection and backdrive
protection on all external I/O lines
• Supports active and passive control of hot plug
detect signal
• Multiport I2C support eliminates need for analog
mux on DDC lines
• Simplified layout with matched 0.5mm trace
spacing
• RoHS-compliant, lead-free packaging
Applications
• PC and consumer electronics
• Digital TV, PC monitors and projectors
Product Description
The CM2031 HDMI Receiver Port Protection and
Interface Device is specifically designed for next
generation HDMI Sink interface protection.
An integrated package provides all ESD, slew rate
limiting on CEC line, level shifting/isolation and
backdrive protection for an HDMI port in a single 38-
Pin TSSOP package.
The CM2031 part is specifically designed to provide
the designer with the most reliable path to HDMI 1.3
CTS compliance.
©2010 SCILLC. All rights reserved.
May 2010 – Rev. 5
Publication Order Number:
CM2031/D

line_dark_gray
CM2031 equivalent
CM2031
www.DataSheet4U.com
For this reason, the CM2031 was designed with an internal I2C accelerator to meet the AC timing specification
even with very long and non-compliant cables.
The internal accelerator works with the source pull-up and the local 47kpullup to increase the positive slew rate
of the DDC_CLK_OUT and DDC_DAT_OUT lines whenever the sensed voltage level exceeds 0.3*5V_SUPPLY
(approximately 1.5V). This provides faster overall risetime in heavily loaded situations without overloading the
mutli-drop open drain I2C outputs elsewhere.
DYNAMIC PULLUPS (CONT’D)
Figure 2. Dynamic DDC Pullups (Discrete - Top, CM2031 - Bottom; 3.3V ASIC - Left, 5V Cable - Right.)
Figure 2 demonstrates the “worst case” operation of the dynamic CM2031 DDC level shifting circuitry (bottom)
against a discrete NFET common-gate level shifter circuit with a typical 1.5kpullup at the source (top.) Both are
shown driving an off-spec, but unfortunately readily available 31m HDMI cable which exceeds the 700pF HDMI
specification. Some widely available HDMI cables have been measured at over 4nF.
When the standard I/OD cell releases the NFET discrete shifter, the risetime is limited by the pullup and the
parasitics of the cable, source and sink. For long cables, this can extend the risetime and reduce the margin for
reading a valid “high” level on the data line. In this case, an HDMI source may not be able to read uncorrupted
data and will not be able to initiate a link.
With the CM2031’s dynamic pullups, when the ASIC driver releases its DDC line and the “OUT” line reaches at
least 0.3*VDD (of 5V_SUPPLY), then the “OUT” active pullups are enabled and the CM2031 takes over driving
the cable until the “OUT” voltage approaches the 5V_SUPPLY rail.
The internal pass element and the dynamic pullups also work together to damp reflections on the longer cables
and keep them from glitching the local ASIC.
I2C LOW LEVEL SHIFTING
In addition to the Dynamic Pullups described in the previous section, then CM2031 also incorporates improved
I2C low-level shifting on the DDC_CLK_IN and DDC_DAT_IN lines for enhanced compatibility.
Typical discrete NFETs level shifters can advertise specifications for low RDS[on], but usually state relatively high
V[GS] test parameters, requiring a 'switch' signal (gate voltage) as high as 10V or more. At a sink current of
Rev. 5 | Page 5 of 18 | www.onsemi.com


line_dark_gray

Preview 5 Page


Part Details

On this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for CM2031 electronic component.


Information Total 18 Pages
Link URL [ Copy URL to Clipboard ]
Download [ CM2031.PDF Datasheet ]

Share Link :

Electronic Components Distributor


An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists.


SparkFun Electronics Allied Electronics DigiKey Electronics Arrow Electronics
Mouser Electronics Adafruit Newark Chip One Stop


Featured Datasheets

Part NumberDescriptionMFRS
CM2030The function is HDMI Receiver Port Protection and Interface Device. ON SemiconductorON Semiconductor
CM2030The function is HDMI Receiver Port Protection and Interface Device. California Micro DevicesCalifornia Micro Devices
CM2031The function is HDMI Receiver Port Protection and Interface Device. ON SemiconductorON Semiconductor

Semiconductors commonly used in industry:

1N4148   |   BAW56   |   1N5400   |   NE555   |  

LM324   |   BC327   |   IRF840  |   2N3904   |  



Quick jump to:

CM20     1N4     2N2     2SA     2SC     74H     BC     HCF     IRF     KA    

LA     LM     MC     NE     ST     STK     TDA     TL     UA    



Privacy Policy   |    Contact Us     |    New    |    Search