DataSheet39.com

What is ICS1894-40?

This electronic component, produced by the manufacturer "Integrated Device Technology", performs the same function as "10BASE-T/100BASE-TX INTEGRATED PHYCEIVER".


ICS1894-40 Datasheet PDF - Integrated Device Technology

Part Number ICS1894-40
Description 10BASE-T/100BASE-TX INTEGRATED PHYCEIVER
Manufacturers Integrated Device Technology 
Logo Integrated Device Technology Logo 


There is a preview and ICS1894-40 download ( pdf file ) link at the bottom of this page.





Total 30 Pages



Preview 1 page

No Preview Available ! ICS1894-40 datasheet, circuit

www.DataSheet4U.com
DATASHEET
10BASE-T/100BASE-TX INTEGRATED PHYCEIVER WITH RMII INTERFACE
ICS1894-40
Description
The ICS1894-40 is a low-power, physical-layer device
(PHY) that supports the ISO/IEC 10Base-T and
100Base-TX Carrier-Sense Multiple Access/Collision
Detection (CSMA/CD) Ethernet standards, ISO/IEC
8802.3. It is intended for RMII/MII, Node/Repeater
applications and includes the Auto-MDIX feature that
automatically corrects crossover errors in plant wiring.
The ICS1894-40 incorporates Digital-Signal Processing
(DSP) control in its Physical-Medium Dependent (PMD)
sub-layer. As a result, it can transmit and receive data on
unshielded twisted-pair (UTP) category 5 cables with
attenuation in excess of 24 dB at 100MHz.
The ICS1894-40 provides a Serial-Management Interface
for exchanging command and status information with a
Station-Management (STA) entity. The ICS1894-40
Media-Dependent Interface (MDI) can be configured to
provide either half-duplex or full-duplex operation at data
rates of 10 Mb/s or 100Mb/s.
In addition, the ICS1894-40 includes a programmable LED
and interrupt output function. The LED outputs can be
configured through registers to indicate the occurance of
certain events such as LINK, COLLISION, ACTIVITY, etc.
The purpose of the programmable interrupt output is to
notify the PHY controller device immediately when a certain
event happens instead of having the PHY controller
continuously poll the PHY. The events that could be used to
generate interrupts are: receiver error, Jabber, page
received, parallel detect fault, link partner acknowledge, link
status change, auto-negotiation complete, remote fault,
collision, etc.
The ICS1894-40 has deep power modes that can result in
significant power savings when the link is broken.
Applications: NIC cards, PC motherboards, switches,
routers, DSL and cable modems, game machines, printers,
network connected appliances, and industrial equipment.
Features
Supports category 5 cables and above with attenuation in
excess of 24dB at 100 MHz.
Single-chip, fully integrated PHY provides PCS, PMA,
PMD, and AUTONEG sub layers functions of IEEE
standard.
10Base-T and 100Base-TX IEEE 8802.3 compliant
MIIM (MDC/MDIO) management bus for PHY register
configuration
RMII interface support with external 50 MHz system clock
Single 3.3V power supply
Highly configurable, supports:
– Media Independent Interface (MII)
– Auto-Negotiation with Parallel detection
– Node applications, managed or unmanaged
– 10M or 100M full and half-duplex modes
– Loopback mode for Diagnostic Functions
Auto-MDI/MDIX crossover correction
Low-power CMOS (typically 300 mW)
Power-Down mode (typically 21mW)
Clock and crystal supported in MII mode
Programmable LEDs
Interrupt output pin
Fully integrated, DSP-based PMD includes:
– Adaptive equalization and baseline-wander
correction
– Transmit wave shaping and stream cipher
scrambler
– MLT-3 encoder and NRZ/NRZI encoder
Core power supply (3.3 V)
3.3 V/1.8 V VDDIO operation supported
Smart power control with deep power down feature
Available in 40-pin (6mm x 6mm) QFN package, Pb-free
Industrial Temp and Lead Free
IDT® 10BASE-T/100BASE-TX INTEGRATED PHYCEIVER WITH RMII INTERFACE
1
ICS1894-40 REV G 060110

line_dark_gray
ICS1894-40 equivalent
ICS1894-40
10BASE-T/100BASE-TX INTEGRATED PHYCEIVER WITH RMII INTERFACE
www.DataSPhHeeYt4CUE.coIVmER
Strapping Options
Pin
Number
1
Pin
Name
AMDIX
16 HWSW/CRS
17 REGPIN/COL
18 AMDIX/RXD2
38 P4/LED2
19 P3/RXD2
12 P2/INT
40 P1/ISO/LED1
39 P0/LED0
21 SI/LED4
20 RXTRI/RXD1
22 FDPX/RXD0
23 RMII/RXDV
24 SPEED
26 ANSEL/RXCLK
27 NOD/RXER
28 SPEED/TXCLK
32 LED3
Pin
Type1
IN/Ipu
IO/Ipd
IO/Ipd
IO/Ipu
IO/Ipu
IO/Ipd
IO/Ipd
IO/
IO/
IO/Ipd
IO/Ipd
IO/Ipu
IO/Ipd
IO/Ipu
IO/Ipu
IO/Ipd
IO/Ipu
IO/Ipu
Pin Function
1 = AMDIX enable
0 = AMDIX disable
Hardware pin select enable. Active during power-on and hardware reset.
Full register access enable. Active during power-on and hardware reset.
1 = AMDIX enable
0 = AMDIX disable
The PHY address is set by P[4:0] at power-on reset. P0 and P1 must have external
pull-up or pull-down to set address at start up.
MII/SI mode select. Active during power-on and hardware reset.
1=Realtime receiver isolation enable3;
0=RX output enable
1=Full duplex
0=Half duplex
Ignored if Auto negotiation is enabled
[1x]=RMII mode
[01]=SI mode (Serial interface mode)
[00]=MII mode
1=100M mode
0=10M mode
1=Enable auto negotiation
0=Disable auto negotiation
0=Node mode
1=repeater mode
1=100M mode
0=10M mode
Ignored if Auto negotiation is enabled
LED3 output
1. IO/Ipu = Digital Input with internal 20k pull-up during power on reset/hardware reset; output pin otherwise.
2. IO/Ipd = Digital Input with internal 20k pull-down during power on reset/hardware reset; output pin otherwise.
3. If RXTRI/RXD1 pin is latched high during power on reset/hardware reset, P1/ISO/LED1 functions as RX real time
isolation control input after latch and LED1 function will be disabled.
Functional Description
The ICS1894-40 is an ethernet PHYceiver. During data
transmission, it accepts sequential nibbles/di-bits from the
MAC (Media Access Control), converts them into a serial bit
stream, encodes them, and transmits them over the medium
through an external isolation transformer. When receiving
data, the ICS1894-40 converts and decodes a serial bit
stream (acquired from an isolation transformer that
interfaces with the medium) into sequential nibbles/di-bits. It
subsequently presents these nibbles/di-bits to the MAC
Interface.
IDT® 10BASE-T/100BASE-TX INTEGRATED PHYCEIVER WITH RMII INTERFACE
5
ICS1894-40 REV G 060110


line_dark_gray

Preview 5 Page


Part Details

On this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for ICS1894-40 electronic component.


Information Total 30 Pages
Link URL [ Copy URL to Clipboard ]
Download [ ICS1894-40.PDF Datasheet ]

Share Link :

Electronic Components Distributor


An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists.


SparkFun Electronics Allied Electronics DigiKey Electronics Arrow Electronics
Mouser Electronics Adafruit Newark Chip One Stop


Featured Datasheets

Part NumberDescriptionMFRS
ICS1894-40The function is 10BASE-T/100BASE-TX INTEGRATED PHYCEIVER. Integrated Device TechnologyIntegrated Device Technology

Semiconductors commonly used in industry:

1N4148   |   BAW56   |   1N5400   |   NE555   |  

LM324   |   BC327   |   IRF840  |   2N3904   |  



Quick jump to:

ICS1     1N4     2N2     2SA     2SC     74H     BC     HCF     IRF     KA    

LA     LM     MC     NE     ST     STK     TDA     TL     UA    



Privacy Policy   |    Contact Us     |    New    |    Search