|
|
Número de pieza | HDBF07001B63 | |
Descripción | SAW FILTER | |
Fabricantes | Shoulder Electronics Limited | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de HDBF07001B63 (archivo pdf) en la parte inferior de esta página. Total 6 Páginas | ||
No Preview Available ! 规格书编号
SPEC NO :
www.DataSheet4U.com
产品规格书
SPECIFICATION
CUSTOMER 客 户:
PRODUCT 产 品:
SAW FILTER
MODEL NO 型 号:
HDBF07001B63 D2712
PREPARED 编 制:
CHECKED 审 核: Houshihong
APPROVED 批 准: CHARLES
D A T E 日 期: 2007-01-25
客户确认 CUSTOMER RECEIVED:
审核 CHECKED
批准 APPROVED
日期 DATE
无锡市好达电子有限公司
Shoulder Electronics Limited
www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected]
Page 1 of 6
1 page SAW FILTER
HDwBwwF.D0a7ta0S0he1eBt4U6.c3om
5. ENVIRONMENTAL CHARACTERISTICS
5-1 High temperature exposure
Subject the device to +85℃ for 16 hours. Then release the filter into the room conditions for 24
hours prior to the measurement. It shall fulfill the specifications in table 1.
5-2 Low temperature exposure
Subject the device to -20℃ for 16 hours. Then release the device into the room conditions for 24
hours prior to the measurement. It shall fulfill the specifications in table 1.
5-3 Temperature cycling
Subject the device to a low temperature of -40℃for 30 minutes. Following by a high temperature of
+80℃ for 30 Minutes. Then release the device into the room conditions for 24 hours prior to the
measurement. It shall meet the specifications in table 1.
5-4 Resistance to solder heat
Dip the device terminals no closer than 1.5mm into the solder bath at 260℃ ±10℃ for 10±1 sec.
Then release the device into the room conditions for 4 hours. The device shall meet the
specifications in table 1.
5-5 Solderability
Subject the device terminals into the solder bath at 245℃ ±5℃ for 5s, More than 95% area of the
terminals must be covered with new solder. It shall meet the specifications in table 1.
5-6 Mechanical shock
Drop the device randomly onto the concrete floor from the height of 1m 3 times. the device shall
fulfill the specifications in table 1.
5-7 Vibration
Subject the device to the vibration for 1 hour each in x,y and z axes with the amplitude of 1.5 mm at
10 to 55 Hz. The device shall fulfill the specifications in table 1.
5-8 Lead fatigue
5-8-1 Pulling test
Weight along with the direction of lead without an shock 1kg. The evice shall satisfy all the initial
Characteristics.
5-8-2 Bending test
Lead shall be subject to withstand against 90℃ bending with 450g weight in the direction of
thickness. This operation shall be done toward both direction. The device shall show no evidence of
damage and shall satisfy all the initial electrical characteristics.
www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected]
Page 5 of 6
5 Page |
Páginas | Total 6 Páginas | |
PDF Descargar | [ Datasheet HDBF07001B63.PDF ] |
Número de pieza | Descripción | Fabricantes |
HDBF07001B63 | SAW FILTER | Shoulder Electronics Limited |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |