SPE0506 Datasheet PDF - SYNC POWER
| Part Number | SPE0506 | |
| Description | 5-Line ESD Protection Array | |
| Manufacturers | SYNC POWER | |
| Logo |  |
|
|
There is a preview and SPE0506 download ( pdf file ) link at the bottom of this page. Total 7 Pages | ||
Preview 1 page No Preview Available !
SPE0506
5-Line ESD Protection Array
DESCRIPTION
The SPE0506 are designed by TVS array that is to protect
sensitive electronics from damage or latch-up due to ESD.
They are designed for use in applications where board
space is at a premium. SPE0506 is bidirectional devices
that will protect up to five lines, and may be used on lines
where the signal polarities swing above and below
ground .
SPE0506 offer desirable characteristics for board level
protection including fast response time, low operating and
clamping voltage, and no device degradation.
SPE0506 may be used to meet the immunity requirements
of IEC 61000-4-2, level 4. The small SOT-23-6L package
makes them ideal for use in portable electronics such as
cell phones, PDA’s, notebook computers, and digital
cameras.
APPLICATIONS
Cellular Handsets and Accessories
Cordless Phone
PDA
Notebooks and Handhelds
Portable Instrumentation
Digital Cameras
MP3 Player
FEATURES
Transient protection for data lines to
IEC 61000-4-2 (ESD) ±15kV (air), ±8kV (contact)
IEC 61000-4-4 (EFT) 40A (5/50ns)
Protects five bidirectional I/O lines
Working voltage: 5V
Low leakage current
Low operating and clamping voltages
PIN CONFIGURATION ( SOT-23-6L )
www.DataSheet4U.com
PART MARKING
2006/03/28 Ver.4
Page 1
|
| |
 
SPE0506
5-Line ESD Protection Array
APPLICATION NOTE
Device Connection for Protection of Five Data Lines
SPE0506 is designed to protect up to five bidirectional data lines. The device is connected as follows:
1. Bidirectional protection of five I/O lines is achieved by connecting pins 1, 3, 4, 5, and 6 to the data lines. Pin 2
is connected to ground. The ground connection should be made directly to the ground plane for best results.
The path length is kept as short as possible to reduce the effects of parasitic inductance in the board traces.
Circuit Board Layout Recommendations for Suppression of ESD
Good circuit board layout is critical for the suppression of ESD induced transients. The following guidelines are
recommended:
1. Place the TVS near the input terminals or connectors to restrict transient coupling.
2. Minimize the path length between the TVS and the protected line.
3. Minimize all conductive loops including power and ground loops.
www4..DTathaSehEeeStD4U.tcroamnsient return path to ground should be kept as short as possible.
5. Never run critical signals near board edges.
6. Use ground planes whenever possible.
2006/03/28 Ver.4
Page 5
Preview 5 Page |
Part DetailsOn this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for SPE0506 electronic component. |
| Information | Total 7 Pages | |
| Link URL | [ Copy URL to Clipboard ] | |
| Download | [ SPE0506.PDF Datasheet ] | |
Share Link :
Electronic Components Distributor
|
An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists. |
| SparkFun Electronics | Allied Electronics | DigiKey Electronics | Arrow Electronics |
| Mouser Electronics | Adafruit | Newark | Chip One Stop |
Featured Datasheets
| Part Number | Description | Manufacturers |
| SPE0504 | The function is 4-Line ESD Protection Array. | SYNC POWER |
| SPE0505 | The function is 5-Line ESD Protection Array. | SYNC POWER |
| SPE0506 | The function is 5-Line ESD Protection Array. | SYNC POWER |
Semiconductors commonly used in industry:
1N4148 |
BAW56 |
1N5400 |
NE555 | | ||
Quick jump to:
SPE0
1N4
2N2
2SA
2SC
74H
BC
HCF
IRF
KA | ||