SPE0504 Datasheet PDF - SYNC POWER
| Part Number | SPE0504 | |
| Description | 4-Line ESD Protection Array | |
| Manufacturers | SYNC POWER | |
| Logo |  |
|
|
There is a preview and SPE0504 download ( pdf file ) link at the bottom of this page. Total 7 Pages | ||
Preview 1 page No Preview Available !
SPE0504
4-Line ESD Protection Array
DESCRIPTION
The SPE0504 are designed by TVS array that is to protect
sensitive electronics from damage or latch-up due to ESD.
They are designed for use in applications where board
space is at a premium. SPE0504 will protect up to four
line, and may be used on lines where the signal polarities
swing above and below ground.
SPE0504 offer desirable characteristics for board level
protection including fast response time, low operating and
clamping voltage, and no device degradation.
SPE0504 may be used to meet the immunity requirements
of IEC 61000-4-2, level 4. The small SOT-23-6L package
makes them ideal for use in portable electronics such as
cell phones, PDA’s, notebook computers, and digital
cameras.
APPLICATIONS
Cellular Handsets and Accessories
Cordless Phone
PDA
Notebooks and Handhelds
Portable Instrumentation
Digital Cameras
MP3 Player
FEATURES
Transient protection for data lines to
IEC 61000-4-2 (ESD) ±15kV (air), ±8kV (contact)
IEC 61000-4-4 (EFT) 40A (5/50ns)
Protects four I/O lines
Working voltage: 5V
Low leakage current
Low operating and clamping voltages
PIN CONFIGURATION ( SOT-23-6L )
www.DataSheet4U.com
PART MARKING
2006/03/28 Ver.4
Page 1 4
|
| |
 
SPE0504
4-Line ESD Protection Array
APPLICATION NOTE
Device Connection for Protection of Four Data Lines
SPE0504 is designed to protect up to four data lines. The device is connected as follows:
1. The TVS protection of four I/O lines is achieved by connecting pins 1, 3, 4 and 6 to the data lines. Pin 2 and 5
are connected to ground. The ground connection should be made directly to the ground plane for best results.
The path length is kept as short as possible to reduce the effects of parasitic inductance.
Circuit Board Layout Recommendations for Suppression of ESD
Good circuit board layout is critical for the suppression of ESD induced transients. The following guidelines are
recommended:
1. Place the TVS near the input terminals or connectors to restrict transient coupling.
2. Minimize the path length between the TVS and the protected line.
3. Minimize all conductive loops including power and ground loops.
www.DataSheet4U.com
4. The ESD transient return path to ground should be kept as short as possible.
5. Never run critical signals near board edges.
6. Use ground planes whenever possible.
2006/03/28 Ver.4
Page 5 4
Preview 5 Page |
Part DetailsOn this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for SPE0504 electronic component. |
| Information | Total 7 Pages | |
| Link URL | [ Copy URL to Clipboard ] | |
| Download | [ SPE0504.PDF Datasheet ] | |
Share Link :
Electronic Components Distributor
|
An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists. |
| SparkFun Electronics | Allied Electronics | DigiKey Electronics | Arrow Electronics |
| Mouser Electronics | Adafruit | Newark | Chip One Stop |
Featured Datasheets
| Part Number | Description | Manufacturers |
| SPE0504 | The function is 4-Line ESD Protection Array. | SYNC POWER |
| SPE0505 | The function is 5-Line ESD Protection Array. | SYNC POWER |
| SPE0506 | The function is 5-Line ESD Protection Array. | SYNC POWER |
Semiconductors commonly used in industry:
1N4148 |
BAW56 |
1N5400 |
NE555 | | ||
Quick jump to:
SPE0
1N4
2N2
2SA
2SC
74H
BC
HCF
IRF
KA | ||