|
|
PDF LM3445 Data sheet ( Hoja de datos )
| Número de pieza | LM3445 | |
| Descripción | Triac Dimmable Offline LED Driver | |
| Fabricantes | National Semiconductor | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de LM3445 (archivo pdf) en la parte inferior de esta página. Total 26 Páginas | ||
|
No Preview Available !
LM3445
February 10, 2009
www.DataSheet4U.com
Triac Dimmable Offline LED Driver
General Description
The LM3445 is an adaptive constant off-time AC/DC buck
(step-down) constant current controller designed to be com-
patible with triac dimmers. The LM3445 provides a constant
current for illuminating high power LEDs and includes a triac
dim decoder. The dim decoder allows wide range LED dim-
ming using standard triac dimmers. The high frequency ca-
pable architecture allows the use of small external passive
components. The LM3445 includes a bleeder circuit to ensure
proper triac operation by allowing current flow while the line
voltage is low to enable proper firing of the triac. A passive
PFC circuit ensures good power factor by drawing current di-
rectly from the line for most of the cycle, and provides a
constant positive voltage to the buck regulator. Additional
features include thermal shutdown, current limit and VCC un-
der-voltage lockout.
Features
■ Triac dim decoder circuit for LED dimming
■ Application voltage range 80VAC – 270VAC
■ Capable of controlling LED currents greater than 1A
■ Adjustable switching frequency
■ Low quiescent current
■ Adaptive programmable off-time allows for constant ripple
current
■ Thermal shutdown
■ No 120Hz flicker
■ Low profile 10 pin MSOP Package
■ Patent pending drive architecture
Applications
■ Retro Fit Triac Dimming
■ Solid State Lighting
■ Industrial and Commercial Lighting
■ Residential Lighting
Typical LM3445 LED Driver Application Circuit
30060301
© 2009 National Semiconductor Corporation 300603
30060305
www.national.com
1 page  
Typical Performance Characteristics
www.DataShefSeWt4Uvs.coInmput Line Voltage
Efficiency vs Input Line Voltage
30060304
BLDR Resistor vs Temperature
VCC UVLO vs Temperature
30060305
30060306
Min On-Time (tON) vs Temperature
30060307
Off Threshold (C11) vs Temperature
30060308
5
30060309
www.national.com
5 Page 
performance vs efficiency. As the holding resistor R5 is in-
creased, the overall efficiency per LM3445 will also increase.
ANGLE DETECT
The Awnwgwle.DDaetateSchteecti4rcUu.ictoumses a comparator with a fixed
threshold voltage of 7.21V to monitor the BLDR pin to deter-
mine whether the triac is on or off. The output of the com-
parator drives the ASNS buffer and also controls the Bleeder
circuit. A 4 µs delay line on the output is used to filter out noise
that could be present on this signal.
The output of the Angle Detect circuit is limited to a 0V to 4.0V
swing by the buffer and presented to the ASNS pin. R1 and
C3 comprise a low-pass filter with a bandwidth on the order
of 1.0Hz.
The Angle Detect circuit and its filter produce a DC level which
corresponds to the duty cycle (relative on-time) of the triac
dimmer. As a result, the LM3445 will work equally well with
50Hz or 60Hz line voltages.
BLEEDER
While the BLDR pin is below the 7.21V threshold, the bleeder
MOSFET is on to place a small load (230Ω) on the series pass
regulator. This additional load is necessary to complete the
circuit through the triac dimmer so that the dimmer delay cir-
cuit can operate correctly. Above 7.21V, the bleeder resistor
is removed to increase efficiency.
FLTR1 PIN
The FLTR1 pin has two functions. Normally, it is fed by ASNS
through filter components R1 and C3 and drives the dim de-
coder. However, if the FLTR1 pin is tied above 4.9V (typical),
e.g., to VCC, the Ramp Comparator is tri-stated, disabling the
dim decoder. See the Master/Slave section.
DIM DECODER
The ramp generator produces a 5.85 kHz saw tooth wave with
a minimum of 1.0V and a maximum of 3.0V. The filtered ASNS
signal enters pin FLTR1 where it is compared against the
output of the Ramp Generator.
The output of the ramp comparator will have an on-time which
is inversely proportional to the average voltage level at pin
FLTR1. However, since the FLTR1 signal can vary between
0V and 4.0V (the limits of the ASNS pin), and the Ramp Gen-
erator signal only varies between 1.0V and 3.0V, the output
of the ramp comparator will be on continuously for VFLTR1 <
1.0V and off continuously for VFLTR1 > 3.0V. This allows a de-
coding range from 45° to 135° to provide a 0 – 100% dimming
range.
The output of the ramp comparator drives both a common-
source N-channel MOSFET through a Schmitt trigger and the
DIM pin (see the Master/Slave section for further functions of
the DIM pin). The MOSFET drain is pulled up to 750 mV by a
50 kΩ resistor.
Since the MOSFET inverts the output of the ramp comparator,
the drain voltage of the MOSFET is proportional to the duty
cycle of the line voltage that comes through the triac dimmer.
The amplitude of the ramp generator causes this proportion-
ality to "hard limit" for duty cycles above 75% and below 25%.
The MOSFET drain signal next passes through an RC filter
comprised of an internal 370 kΩ resistor, and an external ca-
pacitor on pin FLTR2. This forms a second low pass filter to
further reduce the ripple in this signal, which is used as a ref-
erence by the PWM comparator. This RC filter is generally set
to 10Hz.
The net effect is that the output of the dim decoder is a DC
voltage whose amplitude varies from near 0V to 750 mV as
the duty cycle of the dimmer varies from 25% to 75%. This
corresponds to conduction angles of 45° to 135°, respectively.
The output voltage of the Dim Decoder directly controls the
peak current that will be delivered by Q2 during its on-time.
See the Buck Converter section for details.
As the triac fires beyond 135°, the DIM decoder no longer
controls the dimming. At this point the LEDs will dim gradually
for one of two reasons:
1. The voltage at VBUCK decreases and the buck converter
runs out of headroom and causes LED current to
decrease as VBUCK decreases.
2. Minimum on-time is reached which fixes the duty-cycle
and therefore reduces the voltage at VBUCK.
The transition from dimming with the DIM decoder to head-
room or minimum on-time dimming is seamless. LED currents
from full load to as low as 0.5 mA can be easily achieved.
VALLEY-FILL CIRCUIT
VBUCK supplies the power which drives the LED string. Diode
D3 allows VBUCK to remain high while V+ cycles on and off.
VBUCK has a relatively small hold capacitor C10 which reduces
the voltage ripple when the valley fill capacitors are being
charged. However, the network of diodes and capacitors
shown between D3 and C10 make up a "valley-fill" circuit. The
valley-fill circuit can be configured with two or three stages.
The most common configuration is two stages. Figure 8 illus-
trates a two and three stage valley-fill circuit.
FIGURE 8. Two and Three Stage Valley Fill Circuit
11
30060318
www.national.com
11 Page | ||
| Páginas | Total 26 Páginas | |
| PDF Descargar | [ Datasheet LM3445.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| LM344 | High Voltage / High Slew Rate Operational Amplifier | National Semiconductor |
| LM3444 | LM3444 AC-DC Offline LED Driver (Rev. D) |  Texas Instruments |
| LM3445 | LM3445 TRIAC Dimmable Offline LED Driver (Rev. M) | Texas Instruments |
| LM3445 | Triac Dimmable Offline LED Driver | National Semiconductor |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |