|
|
PDF AV-D97 Data sheet ( Hoja de datos )
| Número de pieza | AV-D97 | |
| Descripción | Stereo Receiver | |
| Fabricantes | Aiwa | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de AV-D97 (archivo pdf) en la parte inferior de esta página. Total 30 Páginas | ||
|
No Preview Available !
www.DataSheet4U.com
STEREO RECEIVER
RECEPTOR ESTEREO
AMPLI-TUNER STEREO
AV-D97
OPERATING INSTRUCTIONS
MANUAL DE INSTRUCCIONES
MODE D’EMPLOI
En (English)
E (Español)
F (Français)
For assistance and information
call toll free 1-800-BUY-AIWA
(United States and Puerto Rico)
8A-AR1-903-01
000215ACK-Y-M
U
1 page  
1, 2 and 3 in the illustration correspond to the following details.
www.DataSheet4U.c3omAM antenna
3FM antenna
1Sub woofer
1Speaker system A
Right
Left
2AC outlets
1Speaker system B
Right
Left
Right
1Surround speakers
Left
1Center speaker
CONNECTING SPEAKERS1
Speaker terminals
Connect front speakers (system A and/or B), a center speaker,
surround speakers and sub woofer to the corresponding speaker
terminals on the unit:
- the front speaker cords to the FRONT SPEAKERS terminals
- the center speaker cord to the CENTER SPEAKER terminals
- the surround speaker cords to the SURROUND SPEAKERS
terminals.
- for more powerful bass, the sub woofer (with a built-in amplifier)
cord to the SUB WOOFER 3 jack
When connecting the sub woofer, be sure to select the
“SUBW ON” (sub woofer on) mode (see page 5).
Speaker impedance
• Front and center speakers
Use the same impedance for both the front and center speakers.
The SPEAKER IMPEDANCE SELECTOR on the rear should be
set to the position that matches the impedance value of the front
and center speakers.
When using 4 ohm speakers, set the selector to IMP:4Ω. When
using 8 ohm speakers, set the selector to IMP:8Ω. Please unplug
the AC cord before setting the selector.
• Surround speakers and sub woofer
The SPEAKER IMPEDANCE SELECTOR has no effect on the
SURROUND SPEAKERS terminals and the SUB WOOFER 3
jack. For the surround speakers and sub woofer, use speakers
of 8 ohms or more.
Connecting + to +, – to – terminals
To get the proper sound effect, the speaker terminals on the unit
and the speaker should be connected with proper polarity; the +
terminal on the unit should be connected to the + terminal on
the speaker (and – to –).
NOTE
• Be sure to connect the speaker cords correctly as shown in
the illustration on the right column. Improper connections can
cause short circuits in the SPEAKER(S) terminals.
• Do not leave objects generating magnetism near the speakers.
Front speakers
Wind the tip of the cord
around the terminal.
Then tighten the
terminal. Check that
the cord is connected
securely.
Surround speakers
Sub woofer
En
E (Españo
F (França
Center speaker
4ENGLISH
5 Page 
DSP SURROUND
www.DataSheet4U.com
The DSP (Digital Signal Processor) surround circuits can recreate
the effect of sounds reflected from walls or ceilings, to obtain the
sound presence of real environments. The unit provides 30 DSP
preset modes. Some of them are accompanied with the matching
GEQ preset mode, and you can also select or turn off the GEQ
to suit your preference.
Press the DSP button, and turn the MULTI JOG or
press the N or M button repeatedly until the
desired DSP mode is displayed.
DISCO 1
THEATER
CHURCH
DISCO 2
ARENA 2
CAR
DISCO 3
ARENA 1
PARTY 1
LIVE 1
GAME 2
PARTY 2
LIVE 2
GAME 1
CLASSIC
LIVE 3
MOVIE 2
TV SPORT
HALL 1
MOVIE 1
MUSEUM
HALL 2
JAZZ 2
CONCERT
HALL 3
JAZZ 1
BALLADE 1
STADIUM 1
STADIUM 2
BALLADE 2
When the music source is monaural
The DSP system may not work effectively.
To cancel the selected mode
Press the DSP button to display the DSP mode name, and press
the button again within 4 seconds. “DSP OFF” appears on the
display. Even if canceling the selected DSP mode, the matching
or selected GEQ mode still remains.
To select with the remote control
1 Press the DSP button.
2 Within 4 seconds, press the UP or DOWN button repeatedly
until the desired DSP mode is displayed.
30 preset modes can be selected.
To change the mode rapidly, hold down the UP or DOWN
button.
To adjust the volume and balance of the surround
speakers
Press the MANUAL SELECT button on the remote control three
times to display “SUR 0dB” while the DSP system is turned on.
Then press the N(UP) or M(DOWN) button repeatedly or
turn the MULTI JOG within four seconds.
NOTE
The DSP surround system is automatically canceled and cannot
be turned on:
- When the headphones are plugged in
- When the input signal is 96 kHz
En
E (Españo
F (França
The selected mode name is displayed for four seconds, and the
DSP indicator lights up. When the selected DSP mode is
accompanied with the matching GEQ mode, the GEQ indicator
lights up as well.
Selected mode
ENGLISH 10
11 Page | ||
| Páginas | Total 30 Páginas | |
| PDF Descargar | [ Datasheet AV-D97.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| AV-D97 | Stereo Receiver | Aiwa |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |