|
|
PDF AA51882 Data sheet ( Hoja de datos )
| Número de pieza | AA51882 | |
| Descripción | SERVO MOTOR CONTROLLER | |
| Fabricantes | Agamem Microelectronic | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de AA51882 (archivo pdf) en la parte inferior de esta página. Total 8 Páginas | ||
|
No Preview Available !
www.DataSheet4U.com
PRELIMINARY
AA51882Agamem Microelectronics Inc.
SERVO MOTOR CONTROLLER
■ DESCRIPTION
The AA51882 is an integrated circuit to be applied on servo motor of radio controlled operation.
It provides some flexible functions to tune the servo. External H-Bridge driver will be chosen for
large servo motor application.
■ FEATURES
• Built-in voltage regulator.
• Adjustable dead band range control by external capacitor.
• Fixed pulse width setting to provide start-up power and speed control. .
• Incorporates a protection circuit for "H-Bridge" driving configuration.
• Small outline package – TSSOP16L.
■ APPLICATIONS
• Servo motor control.
• Radio controlled car, boat, and airplane.
• IA products (such as air-condition).
• Remote positioning.
■ BLOCK DIAGRAM
©Copyright Agamem Microelectronics Inc.
1
www.agamem.com.tw 2008/5/5
AGAMEM MICROELECTRONICS INCOPERATION RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE
TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. AGAMEM DOES NOT ASSUME ANY
LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCTS OR CIRCUIT DESRIBED HEREIN; NEITHER
DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS.
1 page  
www.DataSheet4U.com
PRELIMINARY
AA51882Agamem Microelectronics Inc.
SERVO MOTOR CONTROLLER
■ FUNCTIONAL DESCRIPTION
(1) Voltage Regulator
This circuit is composed of a band gap circuit, and outputs a 2.5-volt temperature
compensated reference voltage. This reference voltage is stabilized when the supply voltage
is variable.
(2) Sawtooth wave & One-Shot Generator
Connect a capacitor to CT pin will generate a triangular wave by constant current charging. A
typical value is 0.1uF. The constant current is determined by a resistor connected to RT pin. A
typical capacitor of approximately 0.1uF should be connected in parallel with the resistor to
increase stability.
(3) Servo Position & Over-Time logic
This circuitry consists of a pulse width comparator, which compares the servo position
detection signal (POT pin) from the one-shot timer (CT pin) whose period depends on the
resistance of a potentiometer connected to the servo's drive shaft. This feedback provides the
stability for the control circuitry.
(4) Pulse Stretcher
The difference between the servo control signal and the feedback signal is the error signal.
This error signal is used to toggle the direction of the current flows through the servo. The
function of this pulse stretcher is to “stretch” the small error signal long enough and increases
the duty cycle to the motor for it can maintain sufficient holding force. The circuit also
implements a “dead band” function that prevents servo jitter and hunting. This is a range over
which differences between the input and reference signals will not cause servo operation.
When the signal differences exceed this “dead band” range, the servo will start to shift. The
dead band will change according to the value of capacitor connected to the CDB pin.
(5) Directional Logic Control
The comparator circuit compares pulses from the servo control input (VIN pin) and the voltage
controlled pulse generator. It provides either a positive or a negative output depending on
whether the signal pulse width is larger or smaller than the position generator’s output pulse
(POT pin). Application of this error voltage to the motor driver circuit causes the motor to turn in
a direction that will minimize the error until both pulse widths are the same.
(6) PWM Control
This signal generated by directional logic control block is used to control a flip-flop that toggles
the direction the current flows through the motor. The outputs of the flip-flop drive an external
H-Bridge output driver that handles the high current going through the motor. This output of
this block will be turned on or off with each input pulse based on the status of the directional
logic. The PWM drive techniques provide the benefits of reduced power dissipation, improved
servo motor performance and positively affect system efficiency.
©Copyright Agamem Microelectronics Inc.
5
www.agamem.com.tw 2008/5/5
AGAMEM MICROELECTRONICS INCOPERATION RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE
TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. AGAMEM DOES NOT ASSUME ANY
LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCTS OR CIRCUIT DESRIBED HEREIN; NEITHER
DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS.
5 Page | ||
| Páginas | Total 8 Páginas | |
| PDF Descargar | [ Datasheet AA51882.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| AA51880 | SERVO MOTOR CONTROLLER | Agamem Microelectronic |
| AA51881 | SERVO MOTOR CONTROLLER | Agamem Microelectronic |
| AA51882 | SERVO MOTOR CONTROLLER | Agamem Microelectronic |
| AA51883 | SERVO MOTOR CONTROLLER | Agamem Microelectronic |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |