DataSheet39.com

What is MR-E-70AG?

This electronic component, produced by the manufacturer "MITSUBISHI", performs the same function as "General Purpose AC Servo".


MR-E-70AG Datasheet PDF - MITSUBISHI

Part Number MR-E-70AG
Description General Purpose AC Servo
Manufacturers MITSUBISHI 
Logo MITSUBISHI Logo 


There is a preview and MR-E-70AG download ( pdf file ) link at the bottom of this page.





Total 30 Pages



Preview 1 page

No Preview Available ! MR-E-70AG datasheet, circuit

General-Purpose AC Servo
MODEL
MR-E- A/AG
INSTRUCTION MANUAL
www.DataSheet4U.com
B

line_dark_gray
MR-E-70AG equivalent
(2) Wiring
CAUTION
Wire the equipment correctly and securely. Otherwise, the servo motor may misoperate.
Do not install a power capacitor, surge absorber or radio noise filter (FR-BIF option) between the servo
motor and servo amplifier.
Connect the output terminals (U, V, W) correctly. Otherwise, the servo motor will operate improperly.
Do not connect AC power directly to the servo motor. Otherwise, a fault may occur.
www.DataSheet4U.cTohme surge absorbing diode installed on the DC output signal relay must be wired in the specified direction.
Otherwise, the emergency stop and other protective circuits may not operate.
Servo
Amplifier
External
24VDC
Servo
Amplifier
External
24VDC
Control output
signal
RA
Control output
signal
RA
(3) Test run adjustment
CAUTION
Before operation, check the parameter settings. Improper settings may cause some machines to perform
unexpected operation.
The parameter settings must not be changed excessively. Operation will be insatiable.
(4) Usage
CAUTION
Provide an external emergency stop circuit to ensure that operation can be stopped and power switched
off immediately.
Any person who is involved in disassembly and repair should be fully competent to do the work.
Before resetting an alarm, make sure that the run signal is off to prevent an accident. A sudden restart is
made if an alarm is reset with the run signal on.
Do not modify the equipment.
Use a noise filter, etc. to minimize the influence of electromagnetic interference, which may be caused by
electronic equipment used near the servo amplifier.
Use the servo amplifier with the specified servo motor.
The electromagnetic brake on the servo motor is designed to hold the motor shaft and should not be used
for ordinary braking.
For such reasons as service life and mechanical structure (e.g. where a ballscrew and the servo motor
are coupled via a timing belt), the electromagnetic brake may not hold the motor shaft. To ensure safety,
install a stopper on the machine side.
A- 4


line_dark_gray

Preview 5 Page


Part Details

On this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for MR-E-70AG electronic component.


Information Total 30 Pages
Link URL [ Copy URL to Clipboard ]
Download [ MR-E-70AG.PDF Datasheet ]

Share Link :

Electronic Components Distributor


An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists.


SparkFun Electronics Allied Electronics DigiKey Electronics Arrow Electronics
Mouser Electronics Adafruit Newark Chip One Stop


Featured Datasheets

Part NumberDescriptionMFRS
MR-E-70AThe function is General Purpose AC Servo. MITSUBISHIMITSUBISHI
MR-E-70A-KH003The function is General-Purpose AC Servo. MITSUBISHIMITSUBISHI
MR-E-70A-QW003The function is EZ Motion E Serial. MITSUBISHIMITSUBISHI

Semiconductors commonly used in industry:

1N4148   |   BAW56   |   1N5400   |   NE555   |  

LM324   |   BC327   |   IRF840  |   2N3904   |  



Quick jump to:

MR-E     1N4     2N2     2SA     2SC     74H     BC     HCF     IRF     KA    

LA     LM     MC     NE     ST     STK     TDA     TL     UA    



Privacy Policy   |    Contact Us     |    New    |    Search