DataSheet39.com

What is LM217MX?

This electronic component, produced by the manufacturer "STMicroelectronics", performs the same function as "MEDIUM CURRENT 1.2 TO 37V ADJUSTABLE VOLTAGE REGULATOR".


LM217MX Datasheet PDF - STMicroelectronics

Part Number LM217MX
Description MEDIUM CURRENT 1.2 TO 37V ADJUSTABLE VOLTAGE REGULATOR
Manufacturers STMicroelectronics 
Logo STMicroelectronics Logo 


There is a preview and LM217MX download ( pdf file ) link at the bottom of this page.





Total 11 Pages



Preview 1 page

No Preview Available ! LM217MX datasheet, circuit

LM217M
LM317M
MEDIUM CURRENT
1.2 TO 37V ADJUSTABLE VOLTAGE REGULATOR
s OUTPUT VOLTAGE RANGE : 1.2 TO 37V
s OUTPUT CURRENT IN EXCESS OF 500 mA
s LINE REGULATION TYP. 0.01%
s LOAD REGULATION TYP. 0.1%
s THERMAL OVERLOAD PROTECTION
s SHORT CIRCUIT PROTECTION
s OUTPUT TRANSISTOR SAFE AREA
COMPENSATION
s FLOATING OPERATION FOR HIGH
VOLTAGE APPLICATIONS
DESCRIPTION
The LM217M/LM317M are monolithic integrated
circuits in TO-220, DPAK, SOT-82 and SOT-194
packages intended for use as positive adjustable
voltage regulators.
They are designed to supply until 500 mA of load
current with an output voltage adjustable over a
1.2 to 37V range.
The nominal output voltage is selected by means
of only a resistive divider, making the device
exceptionally easy to use and eliminating the
stocking of many fixed regulators.
SCHEMATIC DIAGRAM
TO-220
SOT-82
DPAK
TO-252
SOT-194
September 1997
1/11

line_dark_gray
LM217MX equivalent
LM217M/LM317M
APPLICATION INFORMATION
The LM317M provides an internal reference
voltage of 1.25V between the output and
adjustments terminals. This is used to set a
constant current flow across an external resistor
divider (see fig. 3), giving an output voltage VO of:
VO = VREF (1 + RR21) + IADJ R2
The device was designed to minimize the term
IADJ (100µA max) and to maintain it very constant
with line and load changes. Usually, the error
term IADJR2 can be neglected. To obtain the
previous requirement, all the regulator quiescent
current is returned to the output terminal,
imposing a minimum load current condition. If the
load is insufficient, the output voltage will rise.
Since the LM317M is a floating regulator and
”sees” only the input-to-outputdifferential voltage,
supplies of very high voltage with respect to
ground can be regulated as long as the maximum
input-to-output differential is not exceeded.
Furthermore, programmable regulator are easily
obtainable and, by connecting a fixed resistor
between the adjustment and output, the device
can be used as a precision current regulator.
In order to optimise the load regulation, the
current set resistor R1 (see fig. 3) should be tied
as close as possible to the regulator, while the
ground terminal of R2 should be near the ground
of the load to provide remote ground sensing.
EXTERNAL CAPACITORS (Fig.5)
Normally no capacitors are needed unless the
device is situated far from the input filter
capacitors; in which case an input bypass is
needed.
A 0.1µF disc or 1µF tantalium input bypass
capacitor (CI) is recommended to reduce the
sensitivity to input line impedance.
The adjustment terminal may be bypassed to
ground to improve ripple rejection. This capacitor
(Cadj) prevents ripple from being amplified as the
output voltage is increased. A 10µF capacitor
should improve ripple rejection about 80dB at
120Hz an a 10V application.
Although the LM317M is stable with no output
capacitance like any feedback circuit, certain
values of external capacitance can cause
excessive ringing. An output capacitance (CO) in
the form of a 1µF tantalium or 25µF aluminium
electrolytic capacitor on the output swamps this
effect and insures stability.
PROTECTION DIODES (Fig.5)
When external capacitors are used with any IC
regulator it is sometimes necessary to add
protection diodes to prevent the capacitors from
discharging through low current points into the
regulator.
Figure 5 show the LM317M with the
recommended protection diodes for output
voltages in excess of 25V or high capacitance
values (C3 > 25µF, C2 > 10µF). Diode D1
prevents C3 from discharging through the IC
during an input short-circuit. The combination of
diodes D1 and D2 prevents C2 from discarging
through the regulator during an input or output
short-circuit.
START-UP BLOCK
It’s not guaranteed the Re-Boot of the device
when the junction temperature is over 85 oC.
5/11


line_dark_gray

Preview 5 Page


Part Details

On this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for LM217MX electronic component.


Information Total 11 Pages
Link URL [ Copy URL to Clipboard ]
Download [ LM217MX.PDF Datasheet ]

Share Link :

Electronic Components Distributor


An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists.


SparkFun Electronics Allied Electronics DigiKey Electronics Arrow Electronics
Mouser Electronics Adafruit Newark Chip One Stop


Featured Datasheets

Part NumberDescriptionMFRS
LM217MThe function is MEDIUM CURRENT 1.2 TO 37V ADJUSTABLE VOLTAGE REGULATOR. STMicroelectronicsSTMicroelectronics
LM217MDTThe function is MEDIUM CURRENT 1.2 TO 37V ADJUSTABLE VOLTAGE REGULATOR. STMicroelectronicsSTMicroelectronics
LM217MSThe function is MEDIUM CURRENT 1.2 TO 37V ADJUSTABLE VOLTAGE REGULATOR. STMicroelectronicsSTMicroelectronics

Semiconductors commonly used in industry:

1N4148   |   BAW56   |   1N5400   |   NE555   |  

LM324   |   BC327   |   IRF840  |   2N3904   |  



Quick jump to:

LM21     1N4     2N2     2SA     2SC     74H     BC     HCF     IRF     KA    

LA     LM     MC     NE     ST     STK     TDA     TL     UA    



Privacy Policy   |    Contact Us     |    New    |    Search