|
|
Datasheet MS21042 Equivalent ( PDF ) |
| N.º | Número de pieza | Descripción | Fabricantes | Category |
| 1 | MS21042 | (MS210xx) Nut
MS21083
LOW PROFILE - NYLON INSERT SUPERSEDES AN364 - MS20364 MAXIMUM TEMP. 250 DEG. F.
TO FIT THREAD SIZE CARBON STEEL AN364 440A 632A 832A 1032A 428A 524A 624A * 820A 918A 1018A MS 21083 N04 N06 N08 N3 N4 N5 N6 N7 N8 N9 N10 CORROSION RESISTANT AN364C C440A C632A C832A C1032A |  Aviaquip | data |
| 2 | MS21042 | MS21042
— .—-—
\
r
\
.&-&
DREION OF WRENCEINO PAO FACES wTw=NwRmmnom cORNEmSm CURNEna MIEwtTtIoi TnGLIUITaoT OPTIONAL IF THE wRExwlNo Z. W, ANO C BEFORE LUBRICATICWAND TRE LM1’1’ OF TRB AREA BETWRBN TRE CORNE3W3SWITRIN. TREMAX3MU?4 LIMCC OF W FQR THE E LENOTE or W4ENCR3NOCO |  Military Specification | data |
| 3 | MS21042 | Nuts MS21042 / NAS1291 Series Specifications
Nuts, Self-locking, 450°, Reduced Hexagon, Reduced Height, Ring Base, Non-Corrosion Resistant Steel
35
Size Dash No. 02 04 06 08 3 4 5 6 7 8 9 10
Thread a 2-56 UNC-3B 4-40 UNC-3B 6-32 UNC-3B 8-32 UNC-3B 10-32 UNF-3B 1/4-28 UNF-3B 5/16-24 UNF-3B 3/8-24 UNF |  Coast Fabrication | data |
| 4 | MS21042L3 | MS21042
— .—-—
\
r
\
.&-&
DREION OF WRENCEINO PAO FACES wTw=NwRmmnom cORNEmSm CURNEna MIEwtTtIoi TnGLIUITaoT OPTIONAL IF THE wRExwlNo Z. W, ANO C BEFORE LUBRICATICWAND TRE LM1’1’ OF TRB AREA BETWRBN TRE CORNE3W3SWITRIN. TREMAX3MU?4 LIMCC OF W FQR THE E LENOTE or W4ENCR3NOCO | Military Specification | data |
MS2 Datasheet ( Hoja de datos ) - resultados coincidentes |
| N.º | Número de pieza | Descripción | Fabricantes | Catagory |
| 1 | MS20001 | Hinge / Butt / Structural / Extruded Genuine Aircraft Hardware Co.
Hinge, Butt, Structural, Extruded
MS20001
TABLE I
* CANCELLED - NO SUPERSEDING PART NUMBER ( a ) TOLERANCES FOR DIMENSIONS ON PITCH SHALL NOT BE CUMULATIVE. ( b ) DIMENSIONS K MUST NEVER EXCEED A FULL LOOP OR TANG, AND BOTH ENDS MUST BE EQUAL WITHIN .020 INCH. INTERC  Genuine Aircraft data | | |
| 2 | MS20001 | STRUCTURAL EXTRUDED HINGE STRUCTURAL EXTRUDED HINGE
STANDARD LENGTH 72 INCHES OTHER LENGTHS AVAILABLE ON REQUEST.
MS20001
Dash Number -2 -3 -4 -5 -6 -8
A Ref Width Open 1.062 1.250 1.500 1.750 2.000 2.000
B (Thickness) Max. Min.
D Loop
Hole Dia. +.005
P Pitch
Pin Diameter
.056
.044
.495
.093
1.00”
.090
.076
 AVIAQUIP data | | |
| 3 | MS20001P | Hinge / Butt / Structural / Extruded INCH-POUND MS20001P 21 May 2012 SUPERSEDING MS20001N 16 November 2010
DETAIL SPECIFICATION SHEET HINGE, BUTT STRUCTURAL, EXTRUDED This specification sheet is approved for use by all Departments and Agencies of the Department of Defense.
FIGURE 1. Butt hinge.
AMSC N/A
FSC 5340
MS20001P TABLE I.  ETC data | | |
| 4 | MS20004 | Diameter / Head Size / Lengths www.datasheet4u.com
www.datasheet4u.com
Genuine Aircraft data | | |
| 5 | MS20004 | MS20004 - MS20014 www.datasheet4u.com
16761 Burke Lane, Huntington Beach, CA 92647 Phone: 714-842-2603 Fax: 714-847-182467 info [email protected]
ETC data | | |
| 6 | MS20005 | Diameter / Head Size / Lengths www.datasheet4u.com
www.datasheet4u.com
Genuine Aircraft data | | |
| 7 | MS20005 | MS20004 - MS20014 www.datasheet4u.com
16761 Burke Lane, Huntington Beach, CA 92647 Phone: 714-842-2603 Fax: 714-847-182467 info [email protected]
ETC data | |
| Esta página es del resultado de búsqueda del MS21042. Si pulsa el resultado de búsqueda de MS21042 se puede ver detalladamente sobre la hoja de datos, el circuito y la disposición de pin. |
nuevas actualizaciones
| Número de pieza | Descripción | Fabricantes | |
| SPS122 | Modern EU gaming Machines require increased +12V current to accommodate the latest gaming peripherals. DC Converters have been engineered with Sanken’s latest technology to efficiently convert redundant power from our lamp gaming PSU and provide additional +12V capacity at the point of use. |
 Sanken |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Sitemap |