EK60 Datasheet PDF - Apex Microtechnology
Part Number | EK60 | |
Description | EVALUATION KIT | |
Manufacturers | Apex Microtechnology | |
Logo | ||
There is a preview and EK60 download ( pdf file ) link at the bottom of this page. Total 3 Pages |
Preview 1 page No Preview Available ! www.DataSheet4U.com
���������������
�������������������������������
����
��������������������������������������������������������������
INTRODUCTION
ASSEMBLY
The EK60 evaluation kit is designed to provide a convenient During assembly refer to Figure 1 and Figure 2.
way to breadboard design ideas for the PA78EU power opera- 1. Solder surface mount ceramic capacitors C4 and C5 on the
tional amplifiers. The EVAL60 evaluation board is pre-wired for
DUT side of the board.
all required and recommended external components including 2. Add components for compensation (CC-, CC+, RC- and RC+)
the ones for power supply bypassing, compensation and cur-
based on the closed loop gain and capacitive load. Add the
rent limiting. The EVAL60 also includes a breadboard area for
current limit resistor (RLIM) based on load requirements (a
constructing your application circuit with provisions for a pre-
minimum value of 4.5 ohms should be used to protect the
amplifier to drive the PA78 inputs.
PARTS LIST
YApex Part #
HS27
EVAL60
Description
Heatsink, Apex
PC Board, Apex
RTW12
Thermal Washer, Apex
OX7R105KWN 1 uF Cap 3530B105K501N
Novacap, 200V Breakdown
140-500N5-330J 33pF Cap CDR-500N5-330KS
AXICON
146510CJ
BNC Connector
MS02
INMS11
Socket Strip
Socket Strip
IMEK60 SCHEMATIC
��� ��
L���
��
E��
PR���
���� ��
���� �� ��� ���
�� �
���
���� �
��� �
��� �
��� �
���
���
Quantity
1
1
1 Box
2
1
3
1 bag
1 bag
�� ���
�
�
�� ���
�
�
���
��
��
PA78 internal output devices). It is recommended to use
MSO2 sockets for the components for quick component
changes on the board. Add 33pF capacitor (CT) between
DUT pins 3 and 5.
3. While developing your application circuit you will probably
want to use the mating socket strip. Use the MS11 socket
strip for mounting the PA78 EU. Clip off the strip after the
12th position. Insert the strip into the circuit board on the
DUT side and solder one pin on the reverse side. Check
whether the mating socket strip is fully seated against the
circuit board and then solder the remaining pins. Insert the
amplifier fully into the socket strip, noting the pin 1 location
on the amplifier and the circuit board.
4. For high power applications (see PA78EU datasheet for
SOA considerations) mount the heat sink (HS27) in the
outlined area on the circuit board.
5. If a heat sink is used, position the thermal washer behind
the amplifier in such a way that the hole on the washer
coincides with the hole on the tab and the heat sink.
6. For high slew rate performance connect the heat tab to
a stable reference (see PA78U datasheet for details).
7. Install the banana jacks for P1 (+Vs), P2 (-Vs) and P3 (GND)
as shown in figure 1 and 2. There are provisions for two
extra banana jacks (P4 and P5) and can be used if desired
for external connections.
�� � �� ���
�� ��
���� �
��� �
���� �
����
�� ��
���
���� ���
�
�
����������������������������������������������
�����������������������������������������
�����������������������������������������
APEX MICROTECHNOLOGY CORPORATION • TELEPHONE (520) 690-8600 • FAX (520) 888-3329 • ORDERS (520) 690-8601 • EMAIL [email protected]
1
|
|
Part DetailsOn this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for EK60 electronic component. |
Information | Total 3 Pages | |
Link URL | [ Copy URL to Clipboard ] | |
Download | [ EK60.PDF Datasheet ] |
Share Link :
Electronic Components Distributor
An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists. |
SparkFun Electronics | Allied Electronics | DigiKey Electronics | Arrow Electronics |
Mouser Electronics | Adafruit | Newark | Chip One Stop |
Featured Datasheets
Part Number | Description | MFRS |
EK60 | The function is EVALUATION KIT. Apex Microtechnology | |
EK62 | The function is EVALUATION KIT. Apex Microtechnology | |
EK6703 | The function is TFT LCD Timing Controller. Fiti | |
Semiconductors commonly used in industry:
1N4148 |  
BAW56 |
1N5400 |
NE555 | | ||
Quick jump to:
EK60
1N4
2N2
2SA
2SC
74H
BC
HCF
IRF
KA |