|
|
Número de pieza | EV1527DR-02A | |
Descripción | 1.3MHz Low Power LED Torch/Flash Driver | |
Fabricantes | MPS | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de EV1527DR-02A (archivo pdf) en la parte inferior de esta página. Total 5 Páginas | ||
No Preview Available ! www.DataSheet4U.com
The Future of Analog IC Technology
DESCRIPTION
The EV1527DR-02A evaluation board is
designed to drive a single Lumileds LED with
low, forward voltage for Camera Flash
applications. The board is set up to obtain
150mA torch current and 750mA flash current
with an input voltage range of 3.0V to 4.2V. The
torch and flash currents can be adjusted by
resistors R2 and R3 on the Evaluation Board.
The MP1527 switches at 1.3MHz and allows
the use of tiny, low cost capacitors and small
inductors. External compensation and soft-start
result in small inrush current and extend the
battery life. The MP1527 operates from an input
voltage as low as 2.6V.
ELECTRICAL SPECIFICATIONS
Parameter
Supply Voltage
LED Current (Torch)
LED Current (Flash)
Symbol
VIN
IOUT1
IOUT2
Value
3.0 – 4.2
150
750
Units
V
mA
mA
EV1527DR-02A
1.3MHz Low Power
LED Torch/Flash Driver
EVALUATION BOARD
FEATURES
• 3V to 4.2V Input Voltage Range
• Tiny Capacitors and Inductors Due to
1.3MHz Fixed Switching Frequency
• Output LED Currents: 150mA at Torch
Mode, 750mA at Flash Mode
• Surface-Mount Components
• Fully Assembled and Tested
APPLICATIONS
• Camera Phone Flash
• Handheld Computers and PDAs
• Digital Still and Video Cameras
• External Modems
• Small LCD Displays
• White LED Drivers
“MPS” and “The Future of Analog IC Technology” are Registered
Trademarks of Monolithic Power Systems, Inc.
EV1527DR-02A EVALUATION BOARD
Load Transient
VIN = 3.6V (1 LED)
(L x W x H) 2.0” x 2.2” x 0.5”
(5.0cm x 5.6cm x 1.0cm)
Board Number
EV1527DR-02A
MPS IC Number
MP1527DR
0
0
VFLASH
2V/div
VOUT
5V/div
EV1527DR-02A_WF01
EV1527DR-02A Rev. 1.0
9/21/2005
www.MonolithicPower.com
MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited.
© 2005 MPS. All Rights Reserved.
1
1 page EV1527DR-02A - 1.3MHZ LOW POWER LED TORCH/FLASH DRIVER
EVALUATION BOARD
QUICK START GUIDE
1. Connect a Lumileds DS25 to LED terminals on the EV1527DR-02A board.
2. Preset the power supply to 3V - 4.2V.
3. Turn the power supply off.
4. Connect the power supply terminals to:
a. Positive (+): VIN
b. Negative (–): GND
5. Connect EN to VIN.
6. Turn on the power supply after making said connections.
7. The MP1527 is enabled on the demo board once VIN is applied.
8. Drive FLASH of Q1 with a pulsed signal (3V or above for High, 0V for Low) to switch between
two (2) LED currents.
9. IOUT1 is set to 150mA on the board.
10. IOUT2 is set to 750mA on the board.
NOTICE: The information in this document is subject to change without notice. Please contact MPS for current specifications.
Users should warrant and guarantee that third party Intellectual Property rights are not infringed upon when integrating MPS
products into any application. MPS will not assume any legal responsibility for any said applications.
EV1527DR-02A Rev. 1.0
9/21/2005
www.MonolithicPower.com
MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited.
© 2005 MPS. All Rights Reserved.
5
5 Page |
Páginas | Total 5 Páginas | |
PDF Descargar | [ Datasheet EV1527DR-02A.PDF ] |
Número de pieza | Descripción | Fabricantes |
EV1527DR-02A | 1.3MHz Low Power LED Torch/Flash Driver | MPS |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |