DataSheet39.com

What is A1147?

This electronic component, produced by the manufacturer "Allegro MicroSystems", performs the same function as "(A1147 / A1148) Low Current Ultrasensitive Two-Wire Chopper-Stabilized Unipolar Hall Effect Switches".


A1147 Datasheet PDF - Allegro MicroSystems

Part Number A1147
Description (A1147 / A1148) Low Current Ultrasensitive Two-Wire Chopper-Stabilized Unipolar Hall Effect Switches
Manufacturers Allegro MicroSystems 
Logo Allegro MicroSystems Logo 


There is a preview and A1147 download ( pdf file ) link at the bottom of this page.





Total 12 Pages



Preview 1 page

No Preview Available ! A1147 datasheet, circuit

A1147 and A1148
Low Current Ultrasensitive Two-Wire Chopper-Stabilized
Unipolar Hall Effect Switches
Features and Benefits
Chopper stabilization
Low switchpoint drift over operating
temperature range
Low sensitivity to stress
Factory programmed at end-of-line for optimized
switchpoints
On-chip protection
Supply transient protection
Reverse-battery protection
On-board voltage regulator
3.5 to 24 V operation
Packages: 3 pin SOT23W (suffix LH), and
3 pin SIP (suffix UA)
Description
The A1147 and A1148 devices are two-wire, unipolar, Hall
effect switches that are factory-programmed at end-of-line to
optimize ultrasensitive magnetic switchpoint accuracy. These
devices use a patented high frequency chopper-stabilization
technique, produced using the Allegro advanced BiCMOS
wafer fabrication process, to achieve magnetic stability and
to eliminate offset inherent in single-element devices exposed
to harsh application environments.
Commonly found in a number of automotive applications,
these switches are utilized to sense seat track position, seat
belt buckle presence, hood/trunk latching, and shift selector
position. Two-wire unipolar switches, such as the A1147
and A1148, are particularly advantageous in price-sensitive
applications because they require one less wire for operation
than do switches with the more traditional open-collector output.
Additionally, the system designer inherently gains diagnostics
because there is always output current flowing, which should
be in either of two narrow ranges. Any current level not within
these ranges indicates a fault condition. These devices also
www.DataSheet4U.com
Not to scale
V+
VCC
0.01 uF
Continued on the next page…
Functional Block Diagram
Clock/Logic
Amp
Regulator
To All Subcircuits
Low-Pass
Filter
A1147-DS, Rev. 8
GND
Package UA Only
GND

line_dark_gray
A1147 equivalent
A1147 and
A1148
Low Current Ultrasensitive Two-Wire
Chopper-Stabilized Unipolar Hall Effect Switches
THERMAL CHARACTERISTICS may require derating at maximum conditions, see application information
Characteristic
Package Thermal Resistance
Symbol
RθJA
Test Conditions*
Package LH, 1-layer PCB with copper limited to solder pads
Package LH, 2-layer PCB with 0.463 in.2 of copper area each side
connected by thermal vias
Package UA, 1-layer PCB with copper limited to solder pads
*Additional thermal information available on Allegro Web site.
Value Units
228 ºC/W
110 ºC/W
165 ºC/W
Power Derating Curve
25
24 VCC(max)
23
22
21
20
19
18
17
16
15
14
13
12
11
2-layer PCB, Package LH
(RθJA = 110 ºC/W)
10
9
1-layer PCB, Package UA
8
7
6
(RθJA = 165 ºC/W)
1-layer PCB, Package LH
5 (RθJA = 228 ºC/W)
4
3
2
VCC(min)
20 40 60 80 100 120 140 160 180
Temperature (ºC)
Power Dissipation versus Ambient Temperature
1900
1800
1700
1600
1500
1400
1300
1200
1100
1000
900
800
700
600
500
400
300
200
100
0
20
(R1θ-JlaAy=e(Rr12θP6J-AlC5ay=BºeC,1r P1/PW0aCc)ºBCk,a/PWga)eckUaAge LH
(1R-θlJaAye=r2P2C8BºC, P/Wac)kage LH
40 60 80 100 120 140 160 180
Temperature (°C)
Allegro MicroSystems, Inc.
5
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
www.allegromicro.com


line_dark_gray

Preview 5 Page


Part Details

On this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for A1147 electronic component.


Information Total 12 Pages
Link URL [ Copy URL to Clipboard ]
Download [ A1147.PDF Datasheet ]

Share Link :

Electronic Components Distributor


An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists.


SparkFun Electronics Allied Electronics DigiKey Electronics Arrow Electronics
Mouser Electronics Adafruit Newark Chip One Stop


Featured Datasheets

Part NumberDescriptionMFRS
A1140The function is Sensitive Two-Wire Chopper-Stabilized Unipolar Hall-Effect Switches. Allegro MicroSystemsAllegro MicroSystems
A1140ELHThe function is Sensitive Two-Wire Chopper-Stabilized Unipolar Hall-Effect Switches. Allegro MicroSystemsAllegro MicroSystems
A1140EUAThe function is Sensitive Two-Wire Chopper-Stabilized Unipolar Hall-Effect Switches. Allegro MicroSystemsAllegro MicroSystems

Semiconductors commonly used in industry:

1N4148   |   BAW56   |   1N5400   |   NE555   |  

LM324   |   BC327   |   IRF840  |   2N3904   |  



Quick jump to:

A114     1N4     2N2     2SA     2SC     74H     BC     HCF     IRF     KA    

LA     LM     MC     NE     ST     STK     TDA     TL     UA    



Privacy Policy   |    Contact Us     |    New    |    Search