M-190G Datasheet PDF - EPSON
Part Number | M-190G | |
Description | Micro DOT Printer | |
Manufacturers | EPSON | |
Logo | ||
There is a preview and M-190G download ( pdf file ) link at the bottom of this page. Total 42 Pages |
Preview 1 page No Preview Available ! www.DataSheet4U.com
Confidential
micro dot printer
M-190G
Specification
Rev. No.
Notes
STANDARD
C
DataSheet4U.com
DataShee
Copied Date
Copied by
,,
SEIKO EPSON CORPORATION
MATSUMOTO MINAMI PLANT
2070 KOTOBUKI KOAKA, MATSUMOTO-SHI, NAGANO, 399-8702 JAPAN
PHONE(0263)86-5353 FAX(0263)86-9923
DataSheet4U.com
DataSheet4 U .com
|
|
www.DataSheet4U.com
Confidential
et4U.com
Explanation of Voltage Terminoloty
In previous specifications for out printers, M-180, M-190, and so on, we identified a usable voltage as
“terminal voltage”; however from this specification for the M-192G on, we will call a usable voltage
“power supply voltage” and also provide voltage ranges, including loss of power supply, voltage when
energizing, and voltage loss from driver and circuit lines.
This is because the previous term, “terminal voltage”, caused confusion between voltage at the
terminals and the power supply voltage.
If the voltage at the terminals is not within specifications, there is a risk that the drivers will not be driven
properly. That’s why we changed it to an expression that could not be misunderstood. Therefore,
this change in terminology doesn’t require a change in the power supply used for M-190 series.
Explanation of Power Supply Voltage
• M-190G power supply voltage 5 ± 0.5 V
(when a stabilized power supply is used);
5 +0.8/-0.5 V (when a Ni-Cd battery is used)
The voltage loss in each terminal, even during sending of current to print solenoids, the voltage
loss in the power supply and loss from loss wiring resistance must be 0.8 V or less. Also, the
voltage loss in the driver circuitry (driver saturation voltage) must be 0.4 V or less.
Compared to this, the specification for the M-190 provides that:
• M-190 terminal voltage
4.8 +0.4/-1.5 V (when a stabilized power supply is used);
4.8 +0.7/-1.5 V (when a Ni-Cd battery is used)
These values are defined as assumed the following conditions:
• M-190 power supply voltage
5 ± 0.5 V
(when a stabilized power supply is used);
5 +0.8/-0.5 V (when a Ni-Cd battery is used)
• The total for the power supplyDvaotlataSgheeleots4sUp.cluosmthe voltage loss from resistance in the wiring plusDataShee
the voltage loss in the driver circuit must be within 1.2 V. (0.8 V + 0.4 V = 1.2 V)
Therefore, the lowest permissible voltage from the driver circuit when energizing is 3.3 V.
([4.5 V - 0.8 V = 3.7 V] - 0.4 V = 3.3 V.)
Also, in either printer mechanism, at the typical print speed, a motor terminal voltage is assumed to be
4.8 V. However, this is obtained by estimating that the voltage loss in the motor terminal during
continuous printing is am average of 0.2 V.
Therefore, there is no substantial terminal difference in the usable ranges of power supply and terminal
voltages between M-190G and M-190.
In either mechanism, the maximum value of the voltage when a Ni-Cd battery is used is 0.3 V above
the 5.5 V maximum when a stabilized power supply is used. This maximum value allows for the
high-voltage situation that occurs temporarily when the Ni-Cd battery is fully charged. This value is not
guaranteed for continuous use.
DataSheet4U.com
DataSheet4 U .com
TITLE
M-190G
Specification
(STANDARD)
SHEET
NO.
REVISION
C NEXT
III
SHEET
II
Preview 5 Page |
Part DetailsOn this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for M-190G electronic component. |
Information | Total 42 Pages | |
Link URL | [ Copy URL to Clipboard ] | |
Download | [ M-190G.PDF Datasheet ] |
Share Link :
Electronic Components Distributor
An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists. |
SparkFun Electronics | Allied Electronics | DigiKey Electronics | Arrow Electronics |
Mouser Electronics | Adafruit | Newark | Chip One Stop |
Featured Datasheets
Part Number | Description | MFRS |
M-190G | The function is Micro DOT Printer. EPSON | |
Semiconductors commonly used in industry:
1N4148 |  
BAW56 |
1N5400 |
NE555 | | ||
Quick jump to:
M-19
1N4
2N2
2SA
2SC
74H
BC
HCF
IRF
KA |